manualshive.com logo in svg

Frontier SB1184, Operator'S Manual

Share
Download
Frontier SB1184 Operator'S Manual Download Page 29

ASSEMBLY 

OM 0408SB1184-A 

27

NOTE:

 

Before

 cutting, make sure the two shafts 

intersect by at least 7 3/4" when in working 
position that is when the snowblower rests on the 
ground. 

3. Figure 

21: 

Hold the two half-shaft side by 

side and locate the 

"L"

 length between the 

two center-to-center half-shaft universal 
joints.  Mark off the zone to be cut on both 
halves opposite each half-shaft guard as 
shown on 

Figure 22.

 

4. Figure 

21A: 

Cut off inner and outer guard 

tubes as well as the inner and outer 
telescopic sections. 

5. Figure 

21A: 

Cut the guard a second time 

leaving the same distance between the end 
of the guard and the end of the shaft as 
existed before.  To obtain the proper distance 
"A" shown on Figure 21A cut the guard 
according to the following table: 

DISTANCE A 

Male PTO 

Female PTO 

1 3/4" 

1 1/4" 

 

6. Figure 

21A: 

File down tubes and remove 

chips. 

7. 

Apply grease to inside of outer telescopic 
section. 

 

IMPORTANT: 

Work with fully guarded shafts 

only. 

 

 

Figure 21A 

A

Figure 21 

Summary of Contents for SB1184





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands