manualshive.com logo in svg

Frontier SB1184, Operator'S Manual

Share
Download
Frontier SB1184 Operator'S Manual Download Page 23

ASSEMBLY 

OM 0408SB1184-A 

21

Installation of Hydraulic Deflector Kit 5RDF009 

(Figures 14-15) 

1. Figure 

14:

 Remove a snap ring (items 1-4) 

from each cylinder pin (items 2-3) and 
remove the pins. Placing the hydraulic ports 
in the position shown on figure 14, attach 
the fixed end of the cylinder (item 6) to the 
chute base (item 5) and the rod end to the 
upper chute bracket with the pins and snap 
rings (items 1-2-3-4). 

2. Figure 15:

 Connect the 3/8" ends of both 

hoses (item 2) to the cylinder (item 1) and 
install a quick coupler with rubber dust cap 
(items 6-7) at the end of each hose.  

3. Figure 

15:  

Secure the hoses

 

on the three 

point hitch with the hose clamp, 3/8" NC x 
1 1/2" lg bolt and 3/8" NC nylon insert nut 
(items 4-3-5) and attach hoses together 
with the nylon tie wraps (item 8) where 
needed.  

Note:

 Make sure to leave enough slack for 

the hoses to allow complete rotation 
movements. 

 

Figure 14 

Figure 15 

Summary of Contents for SB1184





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands