Fronteq FS0507T Operation And Maintenance Manual Download Page 38

Page: 38 / 48

FS0507T

PN 60711000162

5.5.2 Charger Specifications:

ENW-2413

Charger model

ENW-2413

Input voltage

Sing phase100V-220V(50/60Hz)

Input voltage

0V(50/60Hz)MA

X7A

Input voltage

DC24V

Input voltage

MAX13A

MAX12A

Battery weight

EB100

BPC12-120

5.5.3 Battery charging method

1) Connect the power plug of the charger to a 220V power supply.

"Charging", "Charging completed", and "Abnormal" indicator lights will turn off after

turning on.

2) When charging starts, "Charging" (green) lights up.

3) When charging is completed, "Charging End" (red) lights up. Unplug the power cord

after charging

5.5.4 Tips of battery charging

The proper input voltage of the charger is 85 ~ 132V AC or 170 ~ 264V AC. The charger

automatically switches single-phase 100V

•

220V.

5.5.5 Tips for battery charging

1) The machine is deadlocked during charging, the power cannot be turned on, and the

machine cannot be used. When charging is started with the power of this unit turned

Summary of Contents for FS0507T

















































Search results

Summary of Contents for FS0507T

Reviews:

Related manuals for FS0507T

Brands by name

Popular brands

Fronteq FS0507T, Operation And Maintenance Manual

Search results

Summary of Contents for FS0507T

Reviews:

Related manuals for FS0507T

Brands by name

Popular brands