Fronteq FS0507T Operation And Maintenance Manual Download Page 37

Page: 37 / 48

FS0507T

PN 60711000162

No. Name

Function

Charging indicator (green)

The charging status is displayed by

lighting and flashing.

Charging end indicator

（

yellow

）

The charging end status is displayed by

lighting and blinking.

Abnormal indicator

（

red

）

Lights up and flashes when an error

occurs.

Show window

Lights up and flashes when an error

occurs.

Switch

Lights up and flashes when an error

occurs.

Spare interface

Unused

Output display interface

The lower operation panel has a

charging status display function and is

connected to the machine's mains wire.

Output Interface

Connect the wires to the machine body.

Chain interface

Connected to the machine body. The

machine cannot be turned on when not

connected.

Chain interface

Connected to the input line (AC) via an

interlocking line.

Summary of Contents for FS0507T

















































Search results

Summary of Contents for FS0507T

Reviews:

Related manuals for FS0507T

Brands by name

Popular brands

Fronteq FS0507T, Operation And Maintenance Manual

Search results

Summary of Contents for FS0507T

Reviews:

Related manuals for FS0507T

Brands by name

Popular brands