manualshive.com logo in svg

Fristam Pumps FKL 15, Original Instructions Manual, Page: 22 / 40

Share
Download
Fristam Pumps FKL 15 Original Instructions Manual Download Page 22

/ /  FKL PUMP SERIES / / /

22

CAUTION

►

Align the stationary seal ring to the cylindrical pins of the 
mechanical seal chamber.

8. Secure the parts with the snap ring 

(93-1.60)

.

Final assembly of pump casing:

9. Insert O-rings 

(412.70)

 between the both mechanical seal 

chambers.

10. Screw the preassembled mechanical seal chamber with the 

socket screws 

(901.64)

 to the pump casing 

(101)

.

For tightening torques, see table below:

11. Screw the sealing water tube 

(701.60)

 into the mechanical 

seal chamber and seal it.

12. Mount the pump casing on the shafts and slide it onto the 

gearbox.

CAUTION

The pump casing does not lie flat on the gearbox. Material 
damage from warpage of pump casing.

►

Screw the pump casing to the gearbox. The fixture depends 
on the pump size:

– Pump size 25-580: Socket screws in pump casing

For tightening torques, see table below:

13. Subsequently mount the shaft seal of the rotor; for details, 

see 

Chapter 10.9.2, "Mounting of the Rotors," page 24

.

Case E

Preassembly on shaft:

Fig. 32

Rotating seal ring with O-ring

1. Mount the O-ring 

(412.63)

 on the shaft.

2. Slide the rotating seal ring 

(472.60)

 onto the shaft.

CAUTION

►

Slide the rotating seal ring to the cylindrical pins 

(562.68) 

on 

the shaft.

Preassembly of mechanical seal chamber:

Fig. 33

Assembly of mechanical seal chamber

3. Equip the mechanical seal chamber 

(47-2.60)

 with the O-

rings 

(412.65)

 and 

(412.60).

4. Slide the key 

(477.60)

 onto the stationary seal ring 

(475.60)

 

and insert the seal ring and key into the mechanical seal 
chamber.

CAUTION

►

 Align the key and the stationary seal ring to the cylindrical 
pins 

(562.60) 

of the mechanical seal chamber.

Pump Size

Pump casing fastener
Tightening Torque [Nm]

25 - 250

3.4

400

13.5

580

19

Table 9  Tigh

tening torques for pump casing fasteners

Pump Size

Casing screws
Tightening Torque [Nm]

25 - 250

13.5

75 - 580

61

Table 10  Tigh

tening torques for casing screw fasteners

412.63

472.60

101

412.60

47-2.60

914.60

412.65

477.60

475.60

477.61

412.67

504.60

93-1.60

Summary of Contents for FKL 15









































Reviews:

No comments