background image

ELECTRICAL CONNECTIONS

FOR A 3-WIRE SYSTEM

ELECTRIC Laundry Center

6. Attach the white (neutral) wire from the power cord and the
    green ground wire from the appliance harness to the silver-
    colored center terminal on the terminal block. Tighten the
    screw securely.

7. Attach the red and black wires from the power cord to the
     outer brass-colored terminals on the terminal block. Tighten
    both screws securely.
8.  Tighten the screws securing the cord restraint firmly against
     the power cord.
9.  Reinstall the terminal block access cover.

INSTALLATION

1. Run some water from the hot and cold faucets to flush the
    water lines and remove particles that might clog up the
    water valve screens.
2. Check inlet hoses to ensure the rubber washers are installed
    in each end.
3. Carefully connect the inlet hoses to the water valve (on the
     left side of the washer cabinet), tighten by hand, then tighten
    another 2/3 turn with pliers.

                        DO NOT CROSS THREAD OR OVERTIGHTEN
THESE CONNECTIONS.

4. Determine which water faucet is the 

HOT 

water faucet and

   carefully connect the bottom inlet hose to the 

HOT 

water

   faucet, tighten by hand, then tighten another 2/3 turn with
   pliers. Carefully connect the top inlet hose to the 

COLD

   water faucet, tighten by hand, then tighten another 2/3 turn
   with pliers.

                      DO NOT CROSS THREAD OR OVERTIGHTEN
THESE CONNECTIONS. 

Turn the water on and check for leaks

at both connections.

5. Carefully move the laundry center to its final location.

6. To ensure the laundry center is level and solid on all four
     legs, tilt the laundry center forward so the rear legs are
     off the ground. Gently set the laundry center back down to
    allow the rear legs to self adjust. Place a level on top of the
     washer. Check it side to side, then front to back. Screw the
     front leveling legs up or down to ensure the laundry center
     is resting solid on all four legs (no rocking of the laundry
     center should exist).

NOTE: 

Keep the leg extension at a minimum to prevent

excessive vibration.

4. Attach the power cord neutral (central wire) conductor to
    the silver colored center terminal on the terminal block.
    Tighten the screw securely.

1. Remove the screw securing the
    terminal block access cover to the
    rear panel and remove cover.
2. Install a U.L. approved strain relief
    connector in the entry hole on the
    back panel.
3. Insert a NEMA 10-30 Type SRDT,
    U.L. approved power cord
    through the strain relief.

7

Green Ground
Screw

Green
Conductor
(Cord)

Appliance
Green Ground
Wire

Red

White

Black

Terminal Block

Silver Terminal

&$87,21

&$87,21

ELECTRICAL CONNECTIONS

FOR A 4-WIRE SYSTEM

1. Remove the screw securing the
    terminal block access cover to the
    rear panel and remove cover.
2. Install a U.L. approved strain relief
    connector in the entry hole on the
    back panel.
3. Remove the green neutral ground wire
    from the green ground screw located above the termial
    block.
4. Insert a NEMA 14-30 Type ST or SRDT, U.L. approved power
    cord through the strain relief.
5. Attach the green power cord ground wire to the cabinet
    with the green ground screw

5.

6.

7. Reinstall the terminal access cover.

Attach the remaining two power cord outer conductors to
the outer brass colored terminals on the terminal  block.Tighten
both screw securely.
Tighten the screws securing the cord restraint against
the power cord.

ELECTRIC

 

Laundry Center

Summary of Contents for GLET1142CS0









Reviews: