Frigidaire FLCE752CAW0 Use & Care Manual Download | Manualshive

Page: 7 / 52

background image

7

Prevent injury and damage to the
appliance

To prevent serious personal injury and
damage to the laundry center:

•

All repairs and servicing must
be performed by an authorized
service agent unless speciﬁcally
recommended in this

Use & Care

Guide. Use only authorized factory
parts.

•

DO NOT tamper with controls.

•

DO NOT install or store the laundry
center where it will be exposed to
the weather. DO NOT operate the
laundry center in below freezing
temperatures.

•

DO NOT install on carpet. Install
laundry center on a solid ﬂoor. It may
be necessary to reinforce the ﬂoor to
prevent vibration or movement.

•

DO NOT sit on, step on or stand on
the laundry center. DO NOT rest

heavy loads on top. The laundry
center is not meant to support
weight.

•

To reduce the risk of electric shock,
disconnect this appliance from the
power supply before attempting
any user maintenance. Canceling a
cycle or turning the power off at the
console does not disconnect this
appliance from the power supply.

•

This laundry center is equipped with
an electrical overload protector. The
washer motor will stop if it becomes
overheated.

•

A thermal limiter switch automatically
turns off the dryer motor in the
unlikely event of an overheated
situation. A service technician must
replace the thermal limiter switch
after correcting the fault.

•

Failure to comply with these
warnings could result in property
damage or serious personal injuries.

WARNING

FIRE/ELECTRICAL SHOCK HAZARD

Avoid ﬁre hazard or electrical shock. DO NOT use an adapter plug or extension
cord or remove grounding prong from electrical power cord. Failure to follow this
warning can cause serious injury, ﬁre, or death.

IMPORTANT SAFETY INFORMATION

208 v/240 v Electric Dryer

120 v Gas Dryer

UL-approved service
cord must be installed
on electric dryers (not
provided with unit
except those
manufactured for sale
in Canada).

Do not, under
any circumstances,
cut, remove,
or bypass the
grounding prong.

Power cord

with 3-prong

grounded plug

10-30R

3-wire

(fused 30 amp)

14-30R

4-wire

(fused 30 amp)

Grounding

type wall

receptacle

«
...
5
6
7
8
9
...
»

Summary of Contents for FLCE752CAW0





















































Reviews:

No comments

Related manuals for FLCE752CAW0

Brand: Hamilton Beach Commercial Pages: 8

Brand: Sammic Pages: 16

Brand: Malloca Pages: 7

BREKKY AND BANQUET

Brand: Sunbeam Pages: 28

Brand: Summit Pages: 8

Brand: Omcan Pages: 12

Brand: Rommelsbacher Pages: 16

Brand: Lakeland Pages: 12

Brand: La Sommeliere Pages: 14

Brand: Catler Pages: 17

Brand: Tescoma Pages: 3

Brand: U-Line Pages: 46

Brand: German pool Pages: 20

Brand: Royal Catering Pages: 5

Brand: Kalorik Pages: 20

Brand: R.G.V. Pages: 44

Brand: SEVERIN Pages: 68

Brand: Orbegozo Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands