Frigidaire FLCE752CAW0 Use & Care Manual Download

Page: 49 / 52

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSES

SOLUTIONS

Excessive
wrinkling

• Dryer is overloaded.

• Items left in dryer too long.
• Insufficient sorting of items.
• Drying temperature too high.

• DO NOT overload. See Operating

Instructions.

• Remove items as soon as cycle

ends.

• See Operating Instructions.
• Follow fabric care label instructions.

Scratching
or chipping
of the drum
ﬁnish

• Foreign objects such as coins,

pins, clips or buttons are
inside the dryer.*

• Permanently attached items

such as belt buckles, zippers,
and fasteners may be hitting
the inside of the drum.*

• Always remove foreign objects from

pockets before laundering. Remove
objects from drum and restart dryer.

• Turn items inside out before drying

to prevent scratching and damage
to the dryer.

*Drum damage caused by foreign objects or permanently
attached items is not covered by the warranty.

WATER

Wash load
too wet
after spin

• Washer is overloaded.

• Load is out of balance.

• Drain hose is kinked.

• DO NOT overload washer. See

Operating Instructions.

• Rearrange load to allow proper

spinning.

• Straighten drain hose.

Summary of Contents for FLCE752CAW0





















































Search results

Summary of Contents for FLCE752CAW0

Reviews:

Related manuals for FLCE752CAW0

Brands by name

Popular brands

Frigidaire FLCE752CAW0, Use & Care Manual

Search results

Summary of Contents for FLCE752CAW0

Reviews:

Related manuals for FLCE752CAW0

Brands by name

Popular brands