Frigidaire FLCE7522AW Page 51 Use & Care Manual Download

Page: 51 / 54

PROBLEM

POSSIBLE CAUSES

SOLUTIONS

Water does

not enter

washer or it

enters slowly

• Washer lid is open.

• Water supply is not adequate

in area.

• Water supply faucets are not

completely open.

• Water is being used elsewhere

in the house.

• Water inlet hoses are kinked.

• Close washer lid. The washer will

not operate when the lid is open.

• Check another faucet in the

house. Wait until water supply and

pressure increase.

• Fully open hot and cold faucets.

• Water pressure must be at least 10

psi (69 kPa). Avoid running water

elsewhere while washer is filling.

• Straighten hoses.

Warm or hot

water is not

hot enough

• Hot water heater is set too

low or is a distance from

washer.

• Hot water is being used

elsewhere in the house.

• Measure hot water temperature at

nearby faucet with candy or meat

thermometer. Water temperature

should be at least 120°F (50°C).

Adjust water heater as necessary.

• Avoid using hot water elsewhere

before or during washer use. There

may not be enough hot water

available for proper cleaning. If

problem persists, your hot water

system may be unable to support

more than 1 use at a time.

Water in

washer does

not drain or

drains slowly

• Drain hose is kinked or

clogged.

• Clean and straighten the drain

hose.

Water leaks

• Loose fill hose connection at

faucet or washer.

• House drain pipes are

clogged.

• Check and tighten hose

connections. Install rubber sealing

washers provided.

• Unclog drain pipes. Contact

plumber if necessary.

Incorrect

wash

and rinse

temperatures

• Hot and cold water hoses are

connected to wrong supply

faucets.

• Connect hot water hose to hot

water faucet and cold water hose

to cold water faucet.

Water is

entering

washer but

tub does not

fill

• Drain hose standpipe is

incorrect height.

• Standpipe must be a minimum

of 33” (84 cm) high to prevent

siphoning. See

Installation section.

Water is

present in

tub after

wash cycle is

complete

• Lid lock malfunction.

• DO NOT bypass lid lock. Call your

authorized service provider.

The drain

and spin

cycles did

not occur

• Lid lock malfunction.

• DO NOT bypass lid lock. Call your

authorized service provider.

Before Calling (continued)

TROUBLESHOOTING

Summary of Contents for FLCE7522AW























































Search results

Summary of Contents for FLCE7522AW

Reviews:

Related manuals for FLCE7522AW

Brands by name

Popular brands

Frigidaire FLCE7522AW, Use & Care Manual

Search results

Summary of Contents for FLCE7522AW

Reviews:

Related manuals for FLCE7522AW

Brands by name

Popular brands