Frigidaire FLCE7522AW Use & Care Manual Download

Page: 22 / 54

Grounding the gas dryer (USA

and Canada)

1. The laundry center is equipped with

a three-prong (grounding) plug

for your protection against shock

hazard and should be plugged

directly into a properly grounded

three-prong receptacle.

For a grounded, cord-connected dryer:

1. The laundry center MUST be

grounded. In the event of a

malfunction or breakdown,

grounding will reduce the risk of

electrical shock by a path of least

resistance for electrical current.

2. Since your laundry center is

equipped with a power supply cord

having an equipment-grounding

conductor and a grounding plug,

the plug must be plugged into

an appropriate outlet that is

properly installed and grounded

in accordance with all local codes

and ordinances. If in doubt, call a

licensed electrician.

3. DO NOT modify the plug provided

with this appliance. If it will not fit

the outlet, have a proper outlet

installed by a qualified electrician.

WARNING

Improper grounding of the laundry

center may cause serious injury or

death. Check with a licensed electrician

if you are in doubt as to whether the

appliance is properly grounded.

Grounding type wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

1. Turn off power supply to outlet.
2. Remove the screw securing the

terminal block access cover on the

back of the dryer.

3. Install a UL-approved strain relief

according to the power cord/strain

relief manufacturer’s instructions in

the power cord entry hole below the

access panel. At this time, the strain

relief should be loosely in place.

4. Thread an UNPLUGGED, UL-

approved, 30 amp. power cord,

NEMA 10-30 type SRDT, through the

strain relief.

5. Attach the power

cord neutral (center

wire) conductor to

the SILVER colored

center terminal on the

terminal block. Tighten

the screw securely.

Electrical connection

(non-Canada) - 3-wire cord

30 AMP

NEMA 10-30

Neutral

(Center Wire)

3-wire receptacle

(NEMA type 10-

30R)

WARNING

ELECTRICAL SHOCK HAZARD

Failure to disconnect power source

before servicing could result in personal

injury or even death.

2. The plug must be plugged into an

appropriate outlet that is properly

installed and grounded in

accordance with all local codes

and ordinances. If in doubt, call a

licensed electrician.

3. DO NOT modify the plug provided

with this appliance. If it will not fit

the outlet, have a proper outlet

installed by a qualified electrician.

INSTALLATION

SILVER

Terminal

Summary of Contents for FLCE7522AW























































Search results

Summary of Contents for FLCE7522AW

Reviews:

Related manuals for FLCE7522AW

Brands by name

Popular brands

Frigidaire FLCE7522AW, Use & Care Manual

Search results

Summary of Contents for FLCE7522AW

Reviews:

Related manuals for FLCE7522AW

Brands by name

Popular brands