Frigidaire FLCE7522AW Use & Care Manual Download

Page: 20 / 54

Connecting the gas

All connections must be wrench-tightened

Flare

Union

Flare

Union

Manual

Shutoff

Valve

Closed

Open

Flexible

Connector

GAS FLOW

Inlet Pipe on

Back of Dryer

Nipple

Shutoff Valve - Open position

to dryer

from gas supply

1. Remove the shipping cap from gas

pipe at the rear of the dryer.

IMPORTANT

DO NOT connect the dryer to L.P. gas

service without converting the gas

valve. An L.P. conversion kit must be

installed by a qualified gas technician.

2. Connect a 1/2 inch (1.27 cm) I.D.

semi-rigid or approved pipe from

gas supply line to the 3/8 inch (0.96

cm) pipe located on the back of

the dryer. Use a 1/2 inch to 3/8 inch

(1.27 cm to 0.96 cm) reducer for

the connection. Apply an approved

thread sealer that is resistant to the

corrosive action of liquefied gases

on all pipe connections.

IMPORTANT

The supply line must be equipped with

an approved manual shutoff valve. This

valve should be located in the same

room as the dryer and should be in a

location that allows ease of opening

and closing. DO NOT block access to

the gas shutoff valve.

3. Open the shutoff valve in the

gas supply line to allow gas to

flow through the pipe. Wait a few

minutes for gas to move through the

gas line.

4. Check for gas system leaks with a

manometer. If a manometer is not

available, test all connections by

brushing on a soapy water solution.

WARNING

EXPLOSION HAZARD

NEVER test for gas leaks with an open

flame.

The following are specific requirements

for proper and safe electrical installation

of your dryer. Failure to follow these

instructions can create electrical shock

and/or a fire hazard.

Connecting the electrical

system

WARNING

ELECTRICAL SHOCK HAZARD

• This appliance MUST be properly

grounded. Electrical shock can result

if the dryer is not properly grounded.

Follow the instructions in this manual

for proper grounding.

• DO NOT use an extension cord with

this dryer. Some extension cords

are not designed to withstand the

amounts of electrical current this

dryer utilizes and can melt, creating

electrical shock and/or fire hazard.

Locate the dryer within reach of the

receptacle for the length power cord

to be purchased, allowing some slack

in the cord. Refer to the pre-installation

requirements in this manual for the

proper power cord to be purchased.

INSTALLATION

Summary of Contents for FLCE7522AW























































Search results

Summary of Contents for FLCE7522AW

Reviews:

Related manuals for FLCE7522AW

Brands by name

Popular brands

Frigidaire FLCE7522AW, Use & Care Manual

Search results

Summary of Contents for FLCE7522AW

Reviews:

Related manuals for FLCE7522AW

Brands by name

Popular brands