background image

18

CAUTION

If the water supply to your refrigerator is softened, be 

sure the softener is properly maintained. Chemicals 

from a water softener can damage the ice maker.

CAUTION

NEVER use an ice pick or similar sharp instrument to 

break up the ice. This could damage the ice bin and 

dispenser mechanism.
To loosen stuck ice, use warm water. Before replacing 

the ice bin, make sure it is completely dry.

IMPORTANT

When removing or replacing the ice bin, DO NOT rotate 

the auger in the ice bin. If the auger is accidentally rotated, 

you must realign the auger by turning it in 45 degree turns 

(see below) until the ice bin fits into place with the drive 

mechanism. If the auger is not properly aligned when 

replacing the ice bin, the refrigerator will not dispense ice. 

The fresh food door also may not close properly causing 

warm air to leak into the fresh food compartment.

AUTOMATIC ICE & WATER DISPENSER (CONTINUED)

Ice maker/dispenser tips

• 

If your refrigerator is not connected to a water 

supply or the water supply is turned off, turn off the 

ice maker by holding the On/Off soft-touch icon for 

three seconds.

• 

The following sounds are normal when the ice maker 

is operating:

 

-  Motor running

 

-  Ice dropping into ice bin

 

-  Water valve opening or closing

 

-  Running water

• 

When dispensing ice, you will hear a snapping or 

clicking sound when the ice chute opens and closes.

• 

If you need a large quantity of ice at one time, it is 

best to get cubes directly from the ice bin.

•  Ice cubes stored too long may develop an odd flavor. 

Empty the ice bin as explained below.

• 

When dispensing cubed ice, it is normal to have a small 

quantity of little pieces along with the whole cubes.

Cleaning the ice maker 

Clean the ice maker and ice bin at regular intervals, 

especially prior to vacation or moving.
  1  Turn off the ice maker.
  2  Remove the ice bin by 

pulling straight out.

  3  Empty and carefully 

clean the ice bin with 

mild detergent. Do not 

use harsh or abrasive 

cleaners. Rinse with 

clear water.

  4  Allow the ice bin to 

dry completely before 

replacing in the freezer.

  5  Replace the ice bin. 

Turn the ice maker on.

Adjusting Ice Bin Auger

Auger

Removing Ice Bin

Remove and empty the ice bin if:

• 

An extended power failure (one hour or longer) 

causes ice cubes in the ice bin to melt and freeze 

together, jamming the dispenser mechanism.

• 

You do not use the ice dispenser frequently. Ice 

cubes will freeze together in the bin, jamming the 

dispenser mechanism.

Remove the ice bin and shake to loosen the cubes or 

clean as explained above.

Summary of Contents for FFHB2740PP


































Reviews: