Frigidaire FFHB2740PE Page 30 Use And Care Manual Download

Page: 30 / 40

CHANGING THE FILTER

Locating the Filters

Your refrigerator is equipped with water filtering

system. The water filter system filters all

dispensed drinking water, as well as the water

used to produce ice.

Water Filter

The water filter is located at the top right side

of the fresh food compartment.

Ordering Replacement Filters

To order your replacement filters, please visit

our online store at www.frigidaire.com/store,

by calling toll-free at 877-808-4195, or by

visiting the dealer where you purchased your

refrigerator. Frigidaire recommends that you

order extra filters when you first install your

refrigerator, and that you replace your filters at

least once every six months.

Here is the product number to request when

ordering:
PureSource Ultra

Water Filter

Part #ULTRAWF

Replacing the Water Filter

In general, you should change the water filter

every six months to ensure the highest possible

water quality.

Water Filter Status on the user

interface prompts you to replace the filter after

a standard amount of water (200 gallons/757

liters for PureSource Ultra

)

has flowed

through the system.
If your refrigerator has not been used for a period

of time (during moving for example), change the

filter before reinstalling the refrigerator.

Filter Cartridge

Do not use with water that is microbiologically

unsafe or of unknown quality without adequate

disinfection before or after the system. Systems

certified for cyst reduction may be used on

disinfected waters that may contain filterable cysts.

Test & certification results:

•

Rated Capacity - 200 gallons/757 liters for

PureSource Ultra

ice and water filter

• Rated service flow - .50 gallons per minute
•

Operating Temp: Min. 33° F, Max. 100° F

•

Maximum Rated Pressure - 100 pounds per

square inch

•

Recommended Minimum Operating

Pressure: 30 pounds per square inch

To replace your PureSource Ultra

water

filter:
It is not necessary to turn the water supply off

to change the filter. Be ready to wipe up any

small amounts of water released during the

filter replacement.

1 Turn Off the ice maker power switch.

2 Remove the filter by pushing on the end/face

of the filter.

3 Slide the old water filter cartridge straight out

of the housing and discard it.

4 Unpackage the new filter cartridge. Using

the alignment guide, slide it gently into the

filter housing until it stops against the snap-in

connector at the back of the housing.

5 Push firmly until the cartridge snaps into

place (you should hear a click as the cartridge

engages the snap-in connector).

6 Press a drinking glass against the water

dispenser while checking for any leaks at the

filter housing. Any spurts and sputters that

occur as the system purges air out of the

dispenser system are normal.

7 After filling one glass of water, continue

flushing the system for about four minutes.

8 Turn On the ice maker.
9 Press and hold the Water Filter button on the

Ice & Water Dispenser control panel for three

seconds. When the display changes from Red

to Green, the status has been reset.

The PureSource Ultra

ice and

water filter system is tested and

certified to NSF/ANSI Standards 42 and

53 for the reduction of claims specified

on the performance data sheet.

More about your Advanced

Water Filter



NOTE

When ordering your replacement filter,

please reorder the same filter type that is

currently in your refrigerator.

Summary of Contents for FFHB2740PE









































Search results

Summary of Contents for FFHB2740PE

Reviews:

Related manuals for FFHB2740PE

Brands by name

Popular brands

Frigidaire FFHB2740PE, Use And Care Manual

Search results

Summary of Contents for FFHB2740PE

Reviews:

Related manuals for FFHB2740PE

Brands by name

Popular brands