Frigidaire FFHB2740PE Page 12 Use And Care Manual Download

Page: 12 / 40

CAUTION

Drawer is heavy. Use caution when lifting.

DOOR REMOVAL INSTRUCTIONS

Removing Freezer Drawer

1 Open freezer drawer.
2 Remove drawer screws on right and left sides (two screws on each side).

3 Lift drawer up and out to remove.

Installing Freezer Drawer

1 With lower slides pulled out, hang drawer

onto slide brackets ensuring pins on each

side are fully inserted into slots on each side.

6 Tighten four drawer screws.
7 Recheck gasket seal.

8 Install the toe grille by fitting into place.

Push

Against

Freezer

Drawer

Grab Drawer

At Center

From Both

Sides Then

Pull Drawer

Out

Assembly

Drawer Slides

Slot

Cabinet

Drawer

Fully Extend

Install Screws

(2) Each Side

3 Check gasket seal around top, bottom,

and sides of freezer drawer.

4 If gasket is not sealed, open drawer and

slightly loosen four drawer screws (two on

each side) to allow drawer to rotate.

5 Close drawer and recheck the seal on the

gasket (A). Open the drawer grabbing by

the sides in the center (B). Be careful not

to rotate the drawer.

Remove Hex

Head Drawer

Screw

Remove Hex

Head Drawer

Screw

Do Not Remove

Other Screws

Do Not Remove

Other Screws

Remove Hex

Head Drawer

Screw

Remove Hex

Head Drawer

Screw



NOTE

Do not remove center screw from freezer
drawer. This is a factory adjustment.

2 Reinstall four drawer screws (two per

side), tighten down, and close drawer (C).

Summary of Contents for FFHB2740PE









































Search results

Summary of Contents for FFHB2740PE

Reviews:

Related manuals for FFHB2740PE

Brands by name

Popular brands

Frigidaire FFHB2740PE, Use And Care Manual

Search results

Summary of Contents for FFHB2740PE

Reviews:

Related manuals for FFHB2740PE

Brands by name

Popular brands