background image

Wall Sleeve Brands:

Rear Louvers

60

°

7"

60

°

Top View

#7 Whirlpool

23

"

 Deep

1. Redirect the louvers at the back of the wall sleeve as shown 

    opposite. The use of pliers is recommended.

Because of the increased unit depth, first try dry fitting 

using the method described below:

1. Place (2) 1 ½” x 1 ½” x 14” seals against each side. 

2. Gently slide unit in and check if amount extending from the 

    sleeve is sufficient once the trim frame is attached. 

3. If position is okay, remove unit and Proceed to the next step. 

    If not go to step 8.

4. Attach (1) 1 ½” x 1 ½” x 25” long seal in the center at the 

    top of the sleeve. Remove the backing paper and press into 

    position.

5. Attach (2) 1 ½” x 1 ½” x 14” seals to the left and right sides 

    of the sleeve.

6. Cut the 1 ½” x 1 ½” x 25” long seal to 14” long and attach it 

    vertically to the rear grill 7” from the left side. 

7. Attach the tapered spacer blocks to the floor of the sleeve. 

    Now go to step 13.

Use these next steps if the unit requires extra extension 

into the room.

8. Attach 1” x ¾” x 14” long seal over the solid vertical portion

    of the rear grille.

9. Attach (2) 4 ½” x 3 ½” x 1 ½” foam blocks with the slot 

    overlapping the seal above.

10. Install the divider into the slots of the foam blocks. You may 

      need to trim the length to size.

11. Cut the 1 ½” x 1 ½” x 25” seal to fit the top of the sleeve. 

      The pieces must be fitted flush to the edge of the divider.

12. Attach (2) 1 ½” x 1 ½” x 14” seals along the sides of the 

      sleeve again making sure all seals are flush.

13. Center unit & gently slide unit into sleeve. 

14. Before sliding all-the-way back, remove 1st screw from 

      front on left side of unit. 

15. Remove the plastic washer from the screw. 

16. Screw and attach the other end of the ground wire to the 

      unit as shown in picture. Make sure that the toothed washer 

      is against the cabinet.

17. Slide the unit completely to the rear to ensure a good seal, 

      making sure the ground wire does not become tangled.

18. Seal & Frame the unit as described on the last page of 

      these instructions. 

9

8

9

11

12

7

"

5

6

4

Summary of Contents for FAH14ER2T - 14,000-BTU Through-the-Wall Air Conditioner













Reviews: