Frigidaire 318205804 Page 18 Use & Care Manual Download

Page: 18 / 44

BEFORE SETTING OVEN CONTROLS

CAUTION

REMOVE ALL OVEN RACKS and parts before

starting a self-clean cycle.

If the oven racks are left

in the oven during the self-clean cycle, the glide ability

of the Effortless Oven Rack system will be damaged

and will cause all oven racks to loose their shiny

ﬁ nish and or turn blue. Remove

ALL

oven racks and

clean according to instructions provided in the Care &

Cleaning section of this manual.

Make sure the oven and oven racks are COMPLETELY

cooled and safe to touch before attempting to assemble

or disassemble the Effortless™ Oven Rack system.

Never pick up hot oven rack parts.

The Effortless™ oven rack system

Some models are equipped with a special oven rack

system that automatically partially extends the oven rack

from the interior oven glides to assist in easier access to

your food items. This feature works whenever the oven

door is opened or closed.

To assemble the Effortless™ Oven Rack system:

Locate all required parts. You will need the supplied

oven rack (Effortless™ Oven Rack is a ﬂ at rack with a

special dark coating on the left and right rack sides)

and the 2 supplied chrome connector arms.

Open the oven door. Be sure the oven is completely

cool before proceeding.

3. Place the oven rack in positions 1, 2 or 3 only (see

previous page to verify positions). Be sure the rack

connector brackets are at the rear of the range and

pointing towards oven bottom (See Figure 2).

Assemble one connector arm at a time. With the oven

door open and the oven rack in place, install one end

of the connector arm to the hole in the door connec-

tor bracket (Figure 1) and the other end in the hole

in the rack connector bracket (Figure 2 and as in

Figure 3). The oven rack may need to be adjusted in

or out in the rack position to match the length of the

connector arm.

While holding the connector arm in place, twist the

connector arm so the ends of the connector arm

point upwards (See Figures 4 & 5). The connector

arm should now be locked into position.

Repeat steps 4 and 5 for the other connector arm.

Once both connector arms are properly in place, be

sure to test the oven rack operation by gently closing

the oven door. The oven rack should move in and out

of the oven freely when the door is opened or closed.

Door

connector

bracket

Rack

connector

bracket

Oven rack

Connector arm

Open oven door

Connector arm

Left and right

door connector

brackets with

connector arm ends

shown in locked position

(pointing upwards)

Figure 1

Figure 2

Figure 3 - Assembly of the Effortless oven rack

Figure 4

Figure 5

Figure 6 -

oven rack after assembly

Effortless™

Door

connector

bracket

Rack

connector

bracket

Oven rack

Connector arm

Open oven door

Connector arm

Left and right

door connector

brackets with

connector arm ends

shown in locked position

(pointing upwards)

Figure 1

Figure 2

Figure 3 - Assembly of the Effortless oven rack

Figure 4

Figure 5

Figure 6 -

oven rack after assembly

Effortless™

Summary of Contents for 318205804













































Search results

Summary of Contents for 318205804

Reviews:

Related manuals for 318205804

Brands by name

Popular brands

Frigidaire 318205804, Use & Care Manual

Search results

Summary of Contents for 318205804

Reviews:

Related manuals for 318205804

Brands by name

Popular brands