Friendly Robotics RL550 Operating & Safety Manual Download Page 44

Page: 44 / 54

Message Displayed

Probable Cause/Event

Corrective/User Action

Recharge Battery

The maximum operating time has been reached

Connect the charger to the mower

Replace blades

every 200 hours

An automatic reminder to replace the blades is
displayed every 200 hours

Replace the blades and restart the counter of
the blades replacement reminder by choosing
the ‘

Blades replaced – Clear reminder’

option under the ‘

User Preferences’

Replace lamp

The Operating Lamp is burnt out

Confirm the message and replace the
Operating Bulb as soon as possible

Retry elsewhere

Calibration failure from interference in the
immediate area

Move the Robomow 10-12 feet (3-4m) from
this spot and attempt calibration again.

Set Country

Displayed only on first use.

Follow prompts on LCD screen to set country

Set Time

Displayed every time the power pack is taken out
of the mower (reset operation)

Set real time clock (day and hour)

An unknown fault has occurred and user help is
required

Manually drive the mower away from this
particular area and restart operation

Start Elsewhere

Wheel drive motors have been working under a
severe load

Check to insure the mower is not stuck,
allowing the wheels to slip

Enter Code

The theft guard system is activated

Enter the correct 4-digit code. ‘

Theft Guard’

can be deactivated under ‘

User Preferences’

Contact your service provider for assistance in
a lost code situation.

Thermistors fail

Faulty / disconnected thermistors (overheat
protection)

Contact service provider

Time Completed

The operating time set for that zone has been
reached

Connect to the charger if all mowing has been
completed for the day.

7.2 Other Operational or Fault Problems

Problem Encountered

Probable Cause/Event

Corrective/User Action

Batteries are completely

discharged.

Install fresh alkaline C-cell batteries

Batteries installed with wrong

polarity position.

Verify correct placement of batteries.

Perimeter Switch will not

activate when turned on.

Perimeter Switch not installed

vertically and exposed to water/rain.

Water/moisture protection of the Perimeter
Switch can only be insured when mounted
vertically. Replace Perimeter Switch.

Wire disconnected from switch

Confirm wire is plugged in and wire leads are
firmly attached

Perimeter wire cut

Walk along perimeter, including islands and
obstacles excluded with the perimeter wire and
look for obvious cuts or breaks in the wire.
Repair with Robomow wire splice connectors.

'Cut wire’

indicator flashing on

Perimeter Switch

Poor connections

Check and repair all loose/poor or corroded
connections

Summary of Contents for RL550























































Search results

Summary of Contents for RL550

Reviews:

Related manuals for RL550

Brands by name

Popular brands

Friendly Robotics RL550, Operating & Safety Manual

Search results

Summary of Contents for RL550

Reviews:

Related manuals for RL550

Brands by name

Popular brands