background image

GB

4

  After unpacking, make sure that all the components are present. 

If not, contact the Frico agent who sold the appliance to you.

  Frico appliances must be installed by an authorised installer 

who, on completion of the work, will release a declaration of 

conformity to the client in respect of the laws in force and the 

indications given by Frico in the instructions leaflet supplied 

together with the appliance.

  These appliances have been designed both for conditioning 

and/or heating environments and must be destined for this use 

only and compatibly with their performance characteristics.

 

Frico accepts no responsibility, either contractual or extra-

contractual, for any damage caused to persons, animals of 

property as a result of incorrect installation, adjustment or 

maintenance or improper use.

  In case of water leaks, turn the master switch of the system to 

"OFF" and close the water taps.

 

As soon as possible, call professionally qualified personnel and 

do not intervene personally on the appliance.

  If the appliance is not used for a log period of time, the following 

operations should be performed:

Turn the master switch of the system to "OFF"

Close the water taps

-  If there is the risk of freezing, make sure that anti-freeze has 

been added to the system otherwise empty the system.

  If the room temperature is too low ot too high it is damaging for 

the health and is also a useless waste of energy.

  Do not leave the room closed for long periods. Periodically 

open the windows to ensure a correct change of air.

  This instruction leaflet is an integral part of the appliance 

and consequently must be kept carefully and must ALWAYS 

accompany the appliance, even when it is passed to a new 

owner or user or transferred onto another system. 

  All repair or maintenance interventions must be performed 

by the technical service department or by professionally 

qualified personnel as foreseen in this booklet. Do not modify 

or intervene on the appliance as this could create dangerous 

situations and the manufacturer will not be responsible for any 

damage caused.

  Danger from burns - take care when touching

  Remember that some fundamental safety rules should be 

followed when using a product that uses electricity and water, 

such as:

 It is forbidden to carry out any cleaning before having 

disconnected the appliance from the electricity mains supply 

by turning the system master switch to "OFF".

  It is forbidden to modify the safety or adjustment devices 

or adjust without authorisation and indications of the 

manufacturer.

  It is forbidden to pull, cut or knot the electrical cables coming 

out of the appliance, even if it is disconnected from the mains 

supply.

  It is forbidden to poke objects or anything else through the 

inlet or outlet grills.

  It is forbidden to open the doors which access the internal 

parts of the appliance without first turning the system master 

switch to "OFF". 

  It is forbidden to dispose of or leave in the reach of children 

the packaging materials which could become a source of 

danger.

  It is forbidden to climb onto the appliance or rest any object on 

it.  

  The external parts of the appliance can reach temperatures of 

more than 70°C.

General

General warnings

Fundamental safety rules

Summary of Contents for SL-DC1






























Reviews: