background image

21

Error messages:

No Text in 

Significance/ Remedy

Display

Causes

02 Temperature  Ambient

Set up tent if

outside temperature

necessary.

range

outside 
permitted 
range.

03 Resistance Electrical

Check 

contact

outside 

resistance of

for firm 

tolerance

fitting outside  seating/dirt.
tolerance. Maybe 

clean

contacts,
if necessary
replace fitting.

04 Fitting 

Short circuit

Replace fitting,

winding 

in the wire

send in for

short circuit  winding of

checks.

fitting.

05 Fitting Current 

flow

Check 

winding interrupted.

connection 

open circuit

of fusion
plug on fitting.
If okay replace 
the fitting and 
send in for 
checks.

06 Voltage Non- 

Contact

outside permitted 

de- authorised

tolerance

viation of fu-

service point.

sion voltage.

08 Mains Power  Extension 

cable

voltage voltage

too long or cross

outside 

outside 

section too small.

range

permitted Check 

voltage

range during  and connections
fusion. of 

generator.

09 Frequency Frequency  Check 

outside

outside frequency 

of 

range

permitted generator 
range during  voltage.
fusion.

10 Cancel of 

Fusion inter-

– 

fusion rupted 

by 

pressing the 
STOP button. 

FM_2427_2_GB_03_12.qxp:-  28.03.2012  9:28 Uhr  Seite 21

Summary of Contents for FRIAMAT GEO PRINT

























Reviews: