background image

LRS455 Wireless Data Transceiver  

Quick Start Guide

 

 

QSG0016AA Rev B 

7   

 
When setting the transceiver's baud rate, its RS232 data rate is set. The baud rate does not 
have to be the same setting for the two transceivers in the Point-to-Point network. 
 

 

Press 

Esc

 to return to the Main menu. 

 

7.  Press 

2

 in the Main menu to update the Call Book. 

 

 

Enter the Slave serial number in the Master’s Call Book. Enter the Master’s Serial number in 
the Slave’s Call Book, or disable Slave Security (in the Slave).  
 

8.  Press 

3

 in the Main menu. 

 

Set the following parameters so they are identical on both radios in the network: 

o

 

T

x

 Frequency 

o

 

Rx Frequency  

o

 

Max Packet Size 

o

 

Min Packet Size 

o

 

RF Data Rate 

(Only 

RF Data Rate 4

 and 

5

 are approved by the FCC for use in the 

United States.)

 

 

The 

Tx Frequency

 and 

Rx Frequency

 options, or Frequency Key, are located in the 

F

 

submenu after you press 

0

 to access the Frequency Key menu in menu 3. 

 

Changing these values from the factory defaults may help to eliminate interference from other 
networks. 
 

 

Press 

Esc

 to return to the Main menu. 

 

Shortly after both transceivers are plugged in, they should establish a communications link with 
each other and the connection is complete. Using the table below, verify that the radios are 
operating as expected. 
 

9.  Press 

Esc

 to exit the Setup menu and resume normal radio operation. 

 

Point-to-Point Operation LEDs 

 

Master

 

Slave

 

Condition 

Carrier 

Detect 

(CD) 

Transmit  

(TX) 

Clear to  

Send (CTS) 

Carrier 

Detect (CD) 

Transmit 

(TX) 

Clear to  

Send (CTS) 

Powered, no link 

Solid red 

bright 

 

Solid red 

bright

 

Solid red 

bright

 

Solid red 

bright

 

Off 

 

Blinking red 

 

Linked, sending 
sparse data 

Solid 

green

 

Intermittent 

flash 

red

o

 

Intermittent 

flash 

red

o

 

Solid 

green

 

Intermittent 

flash 

red

o

 

Intermittent 

flash 

red

o

 

Master calling 
Slave  

Solid red 

bright

 

Solid red 

dim

 

Solid red 

bright

 

Solid red 

bright

 

Off 

 

Blinking red 

 

Mode 6 - waiting 
for ATD command 

Solid red 

bright

 

Off 

 

Blinking 

red

 

Solid red 

bright

 

Off 

 

Blinking red 

 

Setup Mode 

Solid 

green

 

Solid 

green

 

Solid green

 

Solid 

green

 

Solid 

green

 

Solid 

green

 

 

Summary of Contents for LRS455-C-U









Reviews: