Freescale Semiconductor MCUSLK Manual Download Page 18

MCUSLK_CSM12C32

Rev. 0, 6/2005

How to Reach Us:

USA/Europe/Locations not listed:

Freescale Semiconductor Literature Distribution
P.O. Box 5405, Denver, Colorado 80217
1-800-521-6274 or 480-768-2130

Japan:

Freescale Semiconductor Japan Ltd.
SPS, Technical Information Center
3-20-1, Minami-Azabu
Minato-ku
Tokyo 106-8573, Japan
81-3-3440-3569

Asia/Pacific:

Freescale Semiconductor H.K. Ltd.
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T. Hong Kong
852-26668334

Learn More:

For more information about Freescale 
Semiconductor products, please visit

http://www.freescale.com

Information in this document is provided solely to enable system and software implementers to use 

Freescale Semiconductor products. There are no express or implied copyright licenses granted 

hereunder to design or fabricate any integrated circuits or integrated circuits based on the information 

in this document.

Freescale Semiconductor reserves the right to make changes without further notice to any products 

herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the 

suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any 

liability arising out of the application or use of any product or circuit, and specifically disclaims any 

and all liability, including without limitation consequential or incidental damages. “Typical” parameters 

which may be provided in Freescale Semiconductor data sheets and/or specifications can and do 

vary in different applications and actual performance may vary over time. All operating parameters, 

including “Typicals” must be validated for each customer application by customer’s technical experts. 

Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. 

Freescale Semiconductor products are not designed, intended, or authorized for use as components 

in systems intended for surgical implant into the body, or other applications intended to support or 

sustain life, or for any other application in which the failure of the Freescale Semiconductor product 

could create a situation where personal injury or death may occur. Should Buyer purchase or use 

Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall 

indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and 

distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney 

fees arising out of, directly or indirectly, any claim of personal injury or death associated with such 

unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was 

negligent regarding the design or manufacture of the part.

Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other 
product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2004.

Summary of Contents for MCUSLK



















Reviews: