background image

Document Number: FRDMKE06UG
Rev. 0
03/2014

Information in this document is provided solely to enable system and software 

implementers to use Freescale products. There are no express or implied copyright 

licenses granted hereunder to design or fabricate any integrated circuits based on the 

information in this document.

Freescale reserves the right to make changes without further notice to any products 

herein. Freescale makes no warranty, representation, or guarantee regarding the 

suitability of its products for any particular purpose, nor does Freescale assume any 

liability arising out of the application or use of any product or circuit, and specifically 

disclaims any and all liability, including without limitation consequential or incidental 

damages. “Typical” parameters that may be provided in Freescale data sheets and/or 

specifications can and do vary in different applications, and actual performance may 

vary over time. All operating parameters, including “typicals,” must be validated for 

each customer application by customer’s technical experts. Freescale does not convey 

any license under its patent rights nor the rights of others. Freescale sells products 

pursuant to standard terms and conditions of sale, which can be found at the following 

address: 

freescale.com/SalesTermsandConditions

.

How to Reach Us:

Home Page: 

freescale.com

 

Web Support: 

freescale.com/support

Freescale, the Freescale logo, and Kinetis are trademarks of Freescale 

Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are 

the property of their respective owners. ARM and Cortex are registered trademarks of 

ARM Limited (or its subsidiaries) in the EU and/or elsewhere. All rights reserved.

© 2014 Freescale Semiconductor, Inc.

 

 

Summary of Contents for FRDM-KE06















Reviews: