manualshive.com logo in svg

FRC FDA700 for Delta Winding, Instruction Manual

Share
Download
FRC FDA700 for Delta Winding Instruction Manual Download Page 12

FDA700 Rev160509

12

WIRING

The following figures include the schematics, wiring diagrams, block diagrams, 

and cables for the three phase generator display system.

Connectors and Cables

6 Pin Connector and Cable

Pin  Wire Color  Description 

1 

Red   

+12 VDC

2 

Black  

–12 VDC

3 

White  

Datalink (+)

4 

Green  

Datalink (–)

5 

Blue   

12 VDC

6 

Brown 

Buzzer Ground

Figure 6.  Display Module Wiring

Dual Display

For a dual display configuration a 4-Pin Y-cable (FRC P/N XE-XXDLY4-C1A) 

is connected to the signal interface module 4-Pin connector. Two display extension 

cables (FRC P/N XE-FD7DISP2-C10A) and two display modules can be connected.

1

—

The 6-Pin connector from 

the display module is wired 

to the signal interface 

module 4-Pin connector. 

The two buzzer wires are 

pig-tailed off.

2—Power is supplied to the 

display unit from the signal 

interface module.

Notes

Blue —

Brown — Buzzer –

4-Pin Plug

Connected to the Signal Interface Module

Summary of Contents for FDA700 for Delta Winding





















Reviews:

No comments

Brands by name

Popular brands

Load more brands