Franklin Fueling Systems NANOVAPOR NV-SS ST-1000 Installation And Operation Manual Download Page 49 | Manualshive

Page: 49 / 60

Franklin Fueling Systems NANOVAPOR NV-SS ST-1000 Installation And Operation Manual Download Page 49

45

Accessories

The following accessories are available and may be applicable:

•  Type of flexible ducting to use
•  Vent risers and filters
•  Tank top connection methods and systems
•  Vapour collection vessel (Rocket)
•  Gas detector types and use
•  TankSafe™ product usage and re-order
•  NV-ST-1000 TankSafe™ Delivery Unit spare parts

Part numbers

Description

Part Number

Vent Section (Top) (1x2 m long)

NV-001

Vent Section (Middle) (1x1 m long)

NV-001A

Vent Section (Bottom); comes with Sample Boss (1x2 m long)

NV-002

4" Drop Tube - Single Outlet (1.5 m long)

NV-003

4" Drop Tube - Double Outlet (1.5 m long)

NV-004

3" Drop Tube - Single Outlet (1.5 m long)

NV-005

3" Drop Tube - Doulbe Outlet (1.5 m long)

NV-006

2" Drop Tube - Single Outlet (1.5 m long)

NV-007

198mm - 4" Female Camlock (Cone-Shaped) Adapter

NV-008

4" Tank Adapter; BSPP Male - 3" BSPP Female

NV-009

3" Tank Adapter; BSPP Double Male Barrel Nipple

NV-009a

4" Tank Adapter; Male Camlock - 4" BSPP Female

NV-009b

200 mm x 3 m Flex Duct, Wire Heliz

NV-010

Spiral Hose Bridging Clamp (1 set of 2)

NV-010a

200mm x 6m Flex Duct, Wire Heliz

NV-011

Spiral Hose Bridging Clamp

NV-011a

Air Line Whip Checks (1 set of 4)

NV-012

210mm Anti-Static Lay Flat Duct x 50 m roll (Blk)

NV-014

150mm Anti-Static Lay Flat Duct x 75 m roll (Pink)

NV-015

Diffuser Drop Tube 4" Insert

NV-017

Diffuser Drop Tube 3" Insert

NV-018

Diffuser Drop Tube 2" Insert

NV-019

ST-1000 Spare Pack

NV-020

«
...
47
48
49
50
51
...
»

Summary of Contents for NANOVAPOR NV-SS ST-1000





























































Reviews:

No comments