background image

15

Declaration of conformity

The Omni boiler complies in accordance 
with the following directives: 

2006/95/EC Low Voltage Directive
2011/65/EU RoHS Directive
2009/125/EC Eco Design Directive

Protection Level: IP20

The Omni boiler conforms to the 
requirements of the relevant EU guidelines.

The symbol on the product or on its 
packaging indicates that this product may 
not be treated as household waste. Instead 

it shall be handed over to the applicable collection point for the 
recycling of electrical and electronic equipment. 

By ensuring this product is disposed of correctly, you will help 
prevent potential negative consequences for the environment 
and human health, which could otherwise be caused by 
inappropriate waste handling of this product. 

For more detailed information about recycling of this product, 
please contact your local city offi  ce, your household waste 
disposal service or the shop where you purchased the product.

The Franke Omni 4

-

in

-

1 system is a product 

designed in 

conjunction with 

Greg Rowe Ltd

E

ngland, and is protected by 

the 

following patent applications 

GB1515295.2, GB1515293.7, EP15182884.5, US14/837,640, 
and in China.

NutRunna

® 

 

is a r

egistered trademark.

© Greg Rowe Ltd. All Rights Reserved

Summary of Contents for OMNI 4in1

















Reviews: