Fragram MCOM1256 Manual Download Page 11

 

 

 

 

2. 

Remove the empty spool from the string head. Keep the spring attached to the spool. 

3. 

To install the new spool; make sure the two strings are captured in the slots opposite each other on the new 

spool. Make sure the ends of each string are extended approximately 6 in. (152 mm) beyond each slot. 

4. 

Thread the strings into the eyelets in the string head. Carefully push the spool into the string head (gently pull 

the strings to the outside if necessary). When the spool is positioned in the string head, grasp the strings and 

pull sharply to release them from the slots in the spool. 

5. 

Push down and turn the spool counterclockwise until it no longer turns. Hold the spool down and rotate 

clockwise a small amount. Release the spool. The spool should be locked down in the string head. If not, hold 

down and rotate until locked. 

6. 

Make sure the string head and the spool retainer are installed on the drive shaft. 

 

To install the spool retainer: 

1. 

Turn the spool retainer clockwise for trimmer. Turn the spool retainer counterclockwise for cutter. 

2. 

Pull the strings again to rotate the spool into cutting position. Push the spool retainer down while pulling on 

string(s) to manually advance the string and to check for proper assembly of the string head. 

 

STRING REPLACEMENT 

See Figures 13

14

15 

Use only mon

ofilament string. Use original manufacture’s replacement string for best performance. 

 

 

 

STORAGE (1 MONTH OR LONGER) 

Clean all foreign material from the trimmer. Store it in a well-ventilated place that is inaccessible to children. Keep 

away from corrosive agents such as garden chemicals and de-icing salts. 

 

 

DISPOSAL 

 

This marking indicates that this product should not be disposed with other household 

wastes throughout the EU. To prevent possible harm to the environment or human 

health from uncontrolled waste disposal, recycle it responsibly to promote the 

sustainable reuse of material resources. To return your used device, please use the 

return and collection systems or contact the retailer where the product was 

purchased. They can take this product for environmental safe recycling. 

 

 

 

Summary of Contents for MCOM1256













Reviews: