15
E N G L I S H •
User's Manual
Examples:
1: The container was filled up in 2 minutes with
34 seconds. Divide 19/ 2.56 = 7.42 L/min
Your water flow is 7.42 L/min!
2.56 was got by converting the seconds into
minutes by multiplying 34 x 0.017 = 0.56.
2. The container was filled up in 54 seconds.
Divide 19/ 0.918 = 20.69 L/min
Your water flow is 20.69 L/min!
0.918 was got by multiplying 54 x 0.017 = 0.918.
MAINTENANCE
CLEAN-UP AND STORAGE
When finished using the pressure washer, fol-
low these steps to shut down the unit:
• Turn the pressure washer to the OFF position.
• Turn off the water supply.
• Before disconnecting high-pressure hose con-
nection, point the gun in a safe direction and
discharge the high-pressure water.
• Disconnect high-pressure hose from the pres-
sure washer and gun.
• Disconnect garden hose from the pressure
washer.
• Remove excess water from the pump by tip-
ping the unit on both sides to drain any remain-
ing water from inlet and outlet fittings.
• Remove Water Intake Filter and flush with wa-
ter to remove dirt or debris. Return filter once
cleaned.
• Drain detergent reservoir and flush with run-
ning water.
• Wipe away any remaining water on all parts
and fittings.
• Engage the gun safety lock.
CONTINUED USE OF THE PRESSURE WASHER
WITHOUT WATER SUPPLY ATTACHED WILL
CAUSE SEVERE DAMAGE TO THE UNIT
• Always store the pressure washer, parts, and
accessories in an area with a temperature above
0° C (32° F).
WARNING: FAILURE TO COMPLY WITH
THESE STORAGE INSTRUCTIONS WILL RESULT IN
DAMAGE TO THE PUMP ASSEMBLY.
MAINTENANCE
• This pressure washer is supplied with a closed
lubrication system, so no addition of oil is
needed.
• Check all hoses and accessories for damage
prior to use.
• Check the water intake filter periodically for
deposits. Clean this filter regularly for maxi-
mum performance.
ATTENTION: Follow the maintenance sched-
ule included at the end of this user manual, the
failure to comply with the maintenance plan
established may cause severe damage to your
equipment and void your warranty.
TROUBLESHOOTING
PUMP DOES NOT REACH WORKING PRES-
SURE
Nozzle worn: Replace nozzle.
Water filter fouled: Clean filter.
Water supply pressure low: Turn on water sup-
ply tap fully.
Air being sucked into system: Check tightness of
hose fittings.
Air in pump: Switch off the appliance and keep
depressing and releasing the gun trigger until
the water comes out in a steady flow. Switch the
appliance back on again.
Adjustable nozzle not positioned correctly: Turn
the adjustable nozzle (+).
PRESSURE DROPS DURING USE
Water intake from external tank: Connect appli-
ance to the mains water supply.
Intake water too hot: Reduce temperature.
Nozzle clogged: Clean nozzle.
MOTOR “SOUNDS” BUT FAILS TO START Insuf-
ficient power supply: Check that the volt- age of
the mains power supply line is the same as that
on the plate.
Voltage loss due to use of extension cable:
Check characteristics of extension cable. Appli-
ance not used for a long period of time: Contact
your nearest Authorized Service Center. Prob-
lems with TSS device: Contact your nearest Au-
thorized Service Center.
MOTOR FAILS TO START
No electrical power: Check that the plug is firm-
ly in the socket and that the mains voltage sup-
ply is present.
Problems with TSS device: Contact your nearest
Authorized Service Center.
Appliance not used for a long period of time:
Using the tool unjam the motor from the hole
at the rear of the appliance (in models with this
feature).
