manualshive.com logo in svg

Fox Thermal Instruments FT3, User Manual, Page: 2 / 26

Share
Download
Fox Thermal Instruments FT3 User Manual Download Page 2

This publication must be read in its entirety before performing any operation.  Failure 

to understand and follow these instructions could result in serious personal injury 

and/or damage to the equipment.  Should this equipment require repair or adjustment 

beyond the procedures given herein, contact the factory at:

FOX THERMAL INSTRUMENTS, INC.

399 RESERVATION ROAD

MARINA, CA 93933

TELEPHONE: 831-384-4300

FAX: 831-337-5787

EMAIL: [email protected]

Download Technical Data Sheets from our website: 

www.foxthermalinstruments.com

Fox Thermal Instruments believes that the information provided herein is accurate 

however be advised that the information contained herein is NOT a guarantee 

for satisfactory results.  Specifically, this information is neither a warranty nor 

guarantee, expressed or implied, regarding performance; merchantability; fitness; 

or any other matter with respect to the products; nor recommendation for the use 

of the product/process information in conflict with any patent.  Please note that Fox 

Thermal Instruments, Inc. reserves the right to change and/or improve the product 

design and specification without notice.

Fox FT3 Manuals:

• 

Model FT3 Instruction Manual

• 

Fox FT3 RS485 Modbus Manual

• 

Fox FT3 HART Manual

• 

Fox FT3 View

™

 Software Manual

Notice

Calibration Validation

FO

X THERMAL INSTRUMENTS

2

Summary of Contents for FT3



























Reviews:

No comments