manualshive.com logo in svg

Fox Thermal Instruments FT3, User Manual, Page: 16 / 26

Share
Download
Fox Thermal Instruments FT3 User Manual Download Page 16

i

Performing the CAL-V

™

 Calibration Validation Test

This menu allows the user to confirm the calibration of the FT3 by verifying 
the functionality of the sensor and sensor signal processing circuitry. During 
the CAL-V™ calibration validation test, the microprocessor adjusts current to 
the sensor elements and determines the resulting electrical characteristics. 
These site characteristics are compared with the data that was collected 
at the factory during the original meter calibration. Matching data within 
established tolerances confirms the meter is accurate. This test can be 
performed under no flow or normal flow conditions. The test takes up to four 
minutes to complete. At the conclusion of the test, a Pass or Fail message 
will be displayed. Press 

F4 

at the conclusion of the test to return to normal 

measuring mode or to terminate the test. 
  
Press 

FLO (F2)

 from the main menu. The display will show:

F1 F2 F3 F4

Press 

DGN (F1). 

The display will show:

F1 F2 F3 F4

Press 

TST (F2). 

The display will show: 

F1 F2 F3 F4

Press 

CALV (F1)

 to perform the CAL-V™ verification test. 

Note: The FT3 will stop measuring flow when performing this test. 

Press 

EXIT (F4)

 to exit if you do not wish to continue.  

FLOW PARAMETER 1
    DGN              UNT                PRM              EXIT                                   

            

DIAGNOSTIC

 SIM       TST                    EXIT    

                               

16

Operation: CAL-V

™

CAL-V

™

Calibration Validation

OPERA

TION

            

DIAGNOSTIC

CALV       ZRO                       EXIT

Summary of Contents for FT3



























Reviews:

No comments