manualshive.com logo in svg

Forpark Australia Backhoe, Installation Manual

Share
Download
Forpark Australia Backhoe Installation Manual Download Page 15

 

 

   

 

 

 

14 

FORPARK AUSTRALIA | www.forparkaust.com.au 

INSTALLATION MANUAL – FREE STANDING STATIC 23 
November 2017

 

DOG COURSE WEAVE SPIKES 

 

Build as Senior Swing with top bar at 2.5m. 

The swing frame is best assembled prior to installation.  Assemble the frame while laid 
on the ground then roll into the upright position.  The uprights are fastened to the top 
bar using 25mm tri-lobe bolts. Must use LOCTITE. 

Use the frame in its upright position to determine the correct hole position and dig the holes.  Senior - 2.5m 
from the underside of the top bar to the finished surface level).  Concrete 
the uprights into the ground using footing sizes as shown

. 

Leave the concrete to set for at least 24 hours then attach the seats to the 
top bar using ‘S’ hooks, ensuring that the ‘S’ hooks are fully closed using 
vice-grips.  (The large end of the ‘S’ hook attaches to the swing shackle and 
the small end to the chain, with the lower opening away from the seat.) 

Dig a hole directly below each suspended chain. Attach 
anchors on ends of chains. Allow the chains to hang into 
the holes, ensuring that they are taut and pour concrete 
300x300x300 in each hole. 

 

 

 

 

Summary of Contents for Backhoe




































Reviews:

No comments

Brands by name

Popular brands

Load more brands