manualshive.com logo in svg

Formax FD 280, Operator'S Manual

Share
Download
Formax FD 280 Operator'S Manual Download Page 30

 

 

26 

4.  Press the Lead or Trail arrows to move the tab (s).  

Two presses of the arrow will move the tabs 
almost one eighth of an inch. 

5.  Lift the Stop Button and run tabs.   
6.  Repeat as needed to place tabs where desired. 
7.  If tab placement is drastically altered, tab positions 

are interfering with one another (ex. Lead tab in 
Center area).  Stop and move tabs clear of one 
another or restore factory settings (Section 6.8) 
and begin the adjustment process again. 
 

 
 
 

6.7  Removing Waste 

Backing Paper 

 
1.  Tear the waste backing paper, leaving enough to 

reach and wrap around the TAKE-UP SPINDLE. 

2.  Pull the waste backing paper off the TAKE-UP 

SPINDLE. 

3.  Place backing paper under the TAKE-UP 

SPINDLE from the input end.  

4.  Secure the backing paper to the underside of the  

SPINDLE with tape. 

 

 

6.8 Restore Default 

Tab Settings  

 
All FD 280

’s are set at the factory to meet USPS 

recommended settings.  Each “C” tab is set to the 
center of a piece.  To quickly restore these settings. 
 

1.  Press Stop. 
2. 

Press and hold Head 1 and 2 “L” keys plus both 
the Lead and Trail keys until the lights begin to 
flash. 

3.  Release keys and wait until all lights stop flashing. 

Lift Stop and resume tabbing by selecting the correct 
tab positions for the piece being run. 
 

Summary of Contents for FD 280













































Reviews:

No comments

Brands by name

Popular brands

Load more brands