manualshive.com logo in svg

Formax FD 280, Operator'S Manual

Share
Download
Formax FD 280 Operator'S Manual Download Page 18

 

 

14 

4.3  Control Panel 

                             

 
  

 

Figure 4.3 - FD 280 Control Panel 

 

4.3.1  Power Indicator 

The orange Power Indicator light illuminates when the 
power switch is turned on. 
 

4.3.2  Stop 

The STOP  (red pushbutton mushroom) Switch 
interrupts the movement of all moving parts and 
resets the microprocessor.  Once the STOP button 
has been pressed, it must be lifted up into the run 
position.  Lifting the button will not start the machine.  
Press the STOP switch to change tab mode settings. 
 

4.3.3  Start 

The Start button is a momentary switch that causes 
the resumption of movement after the Stop Switch 
has been pressed.  
 

4.3.4  Tab Ready 

Then green Tab Ready light illuminates when enough 
(usually 3-4) pieces have been fed regularly through 
the machine to allow precise and regular tabbing.  If 
the Tab Ready light stays unlit, there is a problem 
with the feed mechanism as pieces are not being 
counted well. 
 
 

Summary of Contents for FD 280













































Reviews:

No comments

Brands by name

Popular brands

Load more brands