EN
- 3 -
10.-
CLIP
: peak signal indicator light. If dimly lit, or occasionally lit, the output volume should be reduced.
If the indicator light remains on continuously it is due to the high level of the input signal. The volume
of the input signal, therefore, should be reduced.
11.-
PROT
: protection indicator light to signal excessive temperature or overload
12.-
POWER
: power indicator light.
13.-
AC
: light indicator for alternating current (AC) operation.
14.-
DC
: light indicator for direct current (DC) operation.
15.- Device ON/OFF switch.
16.-
MASTER
: MASTER output volume control.
REAR PANEL
ALL
Z1
Z2
Z3
Z4
Z5
Z6
PROT
CLIP
SIG
POWER
AC
DC
INPUT 1
BASS
VOL
VOL
VOL
VOL
VOL
VOL
TREBLE
MASTER
INPUT 2
BASS
TREBLE
INPUT 3
BASS
TREBLE
INPUT 4
BASS
TREBLE
INPUT 5
BASS
TREBLE
INPUT 6
BASS
TREBLE
MPZ-6241
MULTIZONE AMPLIFIER
~ 115 V AC. 50/60 Hz FUSE: T5AL 250 V
~ 230 V AC. 50/60 Hz FUSE: T5AL 250 V
POWER CONSUMPTION: 320 W
P48 V
MIC
LINE
P48 V
MIC
LINE
P48 V
MIC
LINE
P48 V
MIC
CLASS II WIRING
ONE ZONE: 50 W MAX.
TOTAL ALL ZONES: 240 W MAX.
CLASS II WIRING
CHIME
COM
CHIME
SIREN
GAIN
INPUT 4
REMOTE MIC
INPUT 3
MUTE
EMC
TEL
REC
OUT
INPUT
VOL
INPUT 2
INPUT 1
GAIN
SIREN
PUSH
PUSH
PUSH
PUSH
LINE
MULTIZONE AMPLIFIER MPZ-6241
VOL +
VOL -
MODE
REC
1
2 3
1
2
3 4 5 6
7
8
9
10
11
12
13
14
15
16
17
18
4
5 6
7 8 9
1011 12
14
13
15
16
17
1.-
ZONES 100 V OUTPUTS 1
: to turn zones on/off use the front switches. Only loudspeakers with a
100 V line transformer should be used with the zone selection terminals. Connect the positive terminal
of each zone to the corresponding ZONE 1 to ZONE 6 terminal and the common terminal of each
zone to the COM terminal. Maximum power of each zone is 50 W. The total power connected to the
loudspeakers must not exceed the power of the amplifier, 240 W.
2.-
REMOTE MIC
: input terminals
M-62
microphones. It allows you to connect up to 6 microphones in
cascade in one terminal or 3 microphones in cascade in each terminal.
3.-
MUTE
: all inputs and the MP3/FM modules are muted when the contacts of these two terminals are
closed.
4.-
EMC
: emergency signal input connection terminals. This activates all zones and has the highest priority.
5.-
TEL
: telephone input connection terminals. These allow you to connect to a telephone switchboard to
make pages from the switchboard with priority over the other inputs. Consult the characteristics of the
switchboard to adjust to the input level of the amplifier. This has priority over inputs INPUT 1-6.
6.-
VOL
: adjusts the volume of the TEL input.
7.-
REC OUT
: line level output, 2 x RCA connectors.
8.-
INPUT
: line level inputs. Allows you to connect audio sources, 2 x RCA connectors.
9.-
FM ANT.
: FM antenna input connection terminals.
10.-
INPUT 1-4
: microphone/line inputs, XLR combo connector and 6.3 mm jack. Supports balanced
and unbalanced microphone signals and balanced electrect condenser microphones requiring 48 V
phantom power. High level, balanced or unbalanced line signals from mixers, CDs, tape, tuners, etc.
are supported.
11.-
LINE/MIC/P48 V
: These switches have 3 positions:
- LINE: At this position, LINE 1 to LINE 4 inputs can be connected to line-level audio sources, such
as a pre-amplified desktop microphone or the line-level output of a mixer.
- MIC: In this position, balanced or unbalanced, dynamic or electret condenser microphones can
be connected to the LINE 1 to LINE 4 inputs, powered by a battery that does not require phantom
power.
- PHANTOM +48 V: in this position, electret condenser microphones requiring phantom power
(48 V between pins 3 and 1, 2 and 1 of the XLR connector) can be connected to the LINE 1 to LINE
4 inputs. Use this switch at minimum volume to avoid damage.
