manualshive.com logo in svg

Fondital GIAVA KRB 12, Installation, Use And Maintenance Handbook, Page: 12 / 68

Share
Download
Fondital GIAVA KRB 12 Installation, Use And Maintenance Handbook Download Page 12

12

1.3.  

"Comfort" enable/disable function

This function keeps the water heater hot ignoring the existing water heater heating programming, if any (par. 1.10). When the "COMFORT" icon (6, 
fig. 1) is on, the function is enabled. When it is off the function is disabled and the boiler follows the set water heater hour programming.
If “COMFORT” function is enabled (icon “COMFORT” 6 in fig. 1 ON) press “COMFORT” button (G, fig. 1) to disable it.
If “COMFORT” function is disabled (icon “COMFORT”, 6 in fig. 1 OFF) press “COMFORT” button to enable it.
The water heater heating through "COMFORT" function, or programming, is carried out only if the boiler is in SUMMER or WINTER operating mode.
If the boiler is in CH ONLY or OFF operating mode the water heater is not heated.

1. "COMFORT" FUNCTION 

ENABLED

2. PRESS THE 

COMFORT BUTTON

3. "COMFORT" FUNCTION 

DISABLED

Summary of Contents for GIAVA KRB 12





































































Reviews:

No comments