background image

9.0 OPERATING THE APPLIANCE - CONTINUED

8

GB IE

©

 

20

2

1 Focal Point Fires 

Ltd

.

Setting temperature

NOTE: This setting is only applicable for the temperature in standard heating mode, not for the temperature in the timer mode. The default
set temperature is 25°C.
NOTE: The heater only starts working when the set temperature is higher than the room temperature.
Press the + or – key to set the temperature, which ranges from 15 to 30°C.
After the temperature setting has been completed, the display flashes about 5 seconds, then shows the room temperature.

Setting timer

There are up to 9 different timer settings can be programmed.
Each timer setting has its day, power-on time and power-off time.
The maximum duration of each timer setting is 23 hours 50 minutes.
If the power-off time of the timer setting falls on the following day, it is unnecessary to set the day-just set the power-off time.
Press the TIMER SET key, the timer number starts blinking (P1-P9).
Press the + or – key to select a timer number.
Press the TIMER SET key, the cursor on the left side of the day blinks.
Press the 

or 

key to move the cursor to the corresponding day. Press the + key to add a corresponding day, or press the - key to delete

a day. 
Press the TIMER SET key to set the on time. The hour digit starts blinking.
Press the + or – key to set the hour.
Press the TIMER SET key. The minute digit starts blinking.
Press the + or – key to set the minute.
Press the TIMER SET key to set the off time. The hour digit starts blinking.
Press the + or – key to set the hour.
Press the TIMER SET key. The minute digit starts blinking.
Press the + or – key to set the minute.
Press the TIMER SET key. The temperature digit starts blinking.
Press the + or – key to set the temperature.
Press the TIMER SET key to continue with the timer setting or press the OK key to confirm the setting.

Viewing the timer setting

Press the TIMER SET key.
Press the + or – key to check the power-on time of the set timers one by one.
To check the power-off time, press the 

▲ 

key.

Press the + or – key to check the power-off time of the set timers one by one.
To delete selected setting, press the C key.

Activation timer

Press the TIMER ON/OFF key to activate the timer function.
NOTE: When the timer is active, the heating level must be manually selected. If the heater function is not selected; only the flame effect goes
on at the set power-on time.

Open window detection 

Press the 

key to activate open window detection function. The 

icon appears on the display.

The 

icon on the display starts blinking and the heater stops heating if room temperature drops quickly. Press the 

key again to

cancel open window detection.
NOTE: Open window detection does not work if you have not turned heating on.

Settings
Setting weekday and time

Press the DAY/TIME key. When the day is flashing press the 

or 

▼ 

key to select the day.

Press the DAY/TIME key again, then press the + or – key to set the hour.
Press the DAY/TIME key again, then press the + or – key to set the minute.

Press the OK key to confirm the setting.

Standby mode icon

Open window detection

Time/ temperature display

Timer ON

Timer OFF

Temperature/
timer number

Flame brightness level

Timer icon

Day of the week

Low heat setting
High heat setting 

Heating level

Display

Summary of Contents for EF461L-E











Reviews: