background image

9.0

OPERATING THE APPLIANCE

Read All Instructions Before Use 
Check that the heater outlet grille, mounted at the top of the appliance, is not covered or obstructed in any way, and ensure
the power to the fire is switched on. The power to the LCD display panel and the heater functions are controlled using four
switches mounted on the lower right hand side panel.

Controlling the heater functions
The first switch towards the top, marked (0I), controls the main power to the appliance and switches on the LCD display
panel. This feature can be used independently of the heating features. 

The next switch down, marked (*) operates the fan blower without heat, and can be used

for cool air circulation. However for this feature, the main power switch (0I), must also be
in the “on” position.

The next switch down, with a “single bar” marked (I) operates the low heat, (1kW), set-
ting. 

The switch at the bottom, with “two single bars” marked (II), operates the high heat,
(2kW) setting.

To operate the fire in any of the above modes, the top switch marked (OI) must be
switched to the “on” position. 

To operate the fire, the first switch must be turned on firstly, followed by the second
switch to start the blower, if required. To obtain heat from the appliance, the I switch must
then be operated for LOW heat, followed by the II switch for the HIGH heat setting. 

Controlling the LCD display panel - Basic functions

The appliance is pre-programmed with seven different scenes as shown in figures 5

through 11. These scenes have been specially edited to run in a seamless loop. When the

appliance is switched on, the coal fire scene will automatically run. To select a different

scene either press the       button or the       button. This  will skip through all of the dif-

ferent scenes in order. Alternatively, to jump directly to a certain scene press one of the

scene select buttons. For example, button       will play the log fire scene (see figure 5).

Button       will

play the coal fire

scene (see figure

6) and so on.

Certain scenes

also include

sound. This can

be muted by

pressing the

button. The vol-

ume can be low-

ered by pressing

the        button

and raised by

pressing the 

button.

The footage can

be paused by

pressing the 

button. Press

again to resume.

The footage can be speeded up or played backwards by pressing the       or       buttons.

A clock can be made to appear in the top right hand corner of the screen by pressing       .

Press again to hide the clock.

During normal operation the footage may occasionally be seen to ‘freeze’ for a fraction

of a second. This happens as the scene is recycled to loop again. This is perfectly normal

and should be no cause for concern.

Fig. 6 - Log fire

Fig. 11 - Abstract

Fig. 5 - Coal fire

Fig. 7 - Plasma fire (low)

Fig. 8 - Plasma fire (medium)

Fig. 9 - Plasma fire (high)

Fig.10 - River

Figure 12 - Handset basic functions

Clock - on/off

Previous scene

Next scene

Fast forward

Reverse

Mute

Standby/ON

Scene select

Pause/play

Stop

Volume lower

Volume raise

4

1

2

3

4

5

6

7

©

2008 Focal Point Fires plc.

Summary of Contents for EVOKE L23LCD









Reviews: