HearthStone Bristol DX 8762 User Manual Download | Manualshive

Page: 1 / 41

background image

Hearthstone Quality Home Heating Products, Inc. ®

Bristol DX Model 8762

Manual: 6400-40466

R: 1/4/2012

Bristol DX

(Model 8762)

GAS-FIRED DIRECT-VENT HEATER

Owner's Manual

Installation & Operating

Instructions

Read This Manual in Its Entirety

Operate And Maintain This Gas Heater

According To This Instruction Manual.

SAVE THESE INSTRUCTIONS!

WARNING: FOLLOW THE INFORMATION IN
THESE INSTRUCTIONS EXACTLY, IF NOT, A FIRE
OR EXPLOSION MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR
LOSS OF LIFE.

WARNING: DO NOT STORE OR USE GASOLINE
OR ANY OTHER FLAMMABLE VAPORS AND
LIQUIDS NEAR THIS OR ANY OTHER GAS
APPLIANCE.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.
Do not touch electrical switches; do not use the phone

in your building.

Immediately call your gas supplier from a phone

outside the structure. Follow your gas supplier’s
instructions.

If you cannot reach your gas supplier, call the fire

department or 911.

A qualified installer, service agency, or gas supplier must
perform installation and service of this appliance. In the
Commonwealth of Massachusetts, all installation of gas
lines and gas fittings must be performed by a licensed gas
fitter or licensed plumber.

AVERTISSEMENT: ASSUREZ-VOUS DE BIEN
SUIVRE LES INSTRUCTIONS DONNÉ DANS
CETTE NOTICE POUR RÉDUIRE AU MINIMUM LE
RISQUE D’INCENDIE OU POUR ÉVITER TOUT
DOMMAGE MATÉERIEL, TOUTE BLESSURE OU
LA MORT.

AVERTISSEMENT: NE PAS ENTRESPOSER NI
UTILISER D’ESSENCE NI D’AUTRE VAPERURS
OU LIQUIDES INFLAMMABLES DANS LE
VOISINAGE DE CET APPRAREIL OU DE TOUT
AUTRE APPAREIL.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

Ne pas tenter d’allumer d’appareil.
Ne touchez à aucun interrupteur. Ne pas vous servir

des téléphones se trouvant dans le batiment où vous
vous trouvez.

Appelez immédiatement votre fournisseur de gaz

depuis un voisin. Suivez les instructions du
fournisseur.

Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service dos incendies.

L’installation et service doit être exécuté par un qualifié
installer, agence de service ou le fournisseur de gaz.

1
2
3
...
»

Summary of Contents for Bristol DX 8762










































Reviews:

No comments

Related manuals for Bristol DX 8762

Brand: Lasko Pages: 4

Brand: Northern Radiator Pages: 2

Brand: EAST OAK Pages: 14

Brand: Zibro Pages: 12

HORIZON 645CFV Clearview

Brand: Valor Pages: 8

Brand: Winston Pages: 28

Brand: KEKAI Pages: 24

Brand: SUN HoM Pages: 17

Brand: SAMUEL JACKSON Pages: 64

Brand: Cadet Pages: 12

Brand: Nevir Pages: 28

Brand: Cadet Pages: 10

Brand: Envirovent Pages: 28

Brand: Lifestyle Pages: 15

Brand: TE Connectivity Pages: 55

SunWarmth CIR 150-1 I

Brand: STIEBEL ELTRON Pages: 56

Brand: Perel Pages: 17

Brand: Comfort Glow Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands