FOAMICO 7009077 Manual Download Page 8

 

 

8 B 540-27-F + feed pump_7009077  US – 07-02-2019 

 

 DANGER 

Electrocution hazard 

Unprofessional work on the electric equipment can result in severe injury 
and death. 

Switch of the power supply, before connecting or removing a plug from electric 
outlets. 

 

 

NOTICE 

Use only original FOAMICO Nozzles, hoses, couplings and spare parts. 

2.2   Precautionary measures  

The construction of the system is in accordance with the generally adopted, technical requirements and the 
stipulations concerning working environment and accident prevention. Therefore the equipment must be in 
its best technical state before being used, and must only be utilized according to its requirements and by 
observance of the precautionary measures and operational instructions. Disturbances, which might influence 
the safety, must be rectified immediately.  

2.3  Appropriate utilization  

FOAMICO low-pressure system is manufactured with the purpose of:  
Rinsing with water, spreading foam and sanitizer within the stated boundaries. 
 
Any other kind of application or use beyond this is considered to be inappropriate and deviant concerning the 
requirements, and may lead to dangerous situations. FOAMICO is not liable for any sequential damages 
brought about by this. 
Appropriate utilization includes the following: 
 
The instructions, regulations, and recommendations given in this manual. 
The observance of the prescribed intervals for inspection and maintenance. 
The correct maintenance for good operational condition of the system. 
The observance of the prescribed conditions for the environment and operation 
 

 

 DANGER 

Risk of chemical burns 

Improper handling of chemicals results in a risk of chemical burns.  

When handling chemicals, ensure that the information provided by the chemical 
supplier is strictly observed. 

The foam is adjusted by means of maximum nozzles, be sure to observe recommendations of the respective 
chemical supplier.  

Summary of Contents for 7009077



























Reviews: