FNW FNW7XX Installation Instructions Manual Download Page 20

RESILIENT-SEATED CARTRIDGE STYLE

FNW7XX

BUTTERFLY VALVE

INSTALLATION INSTRUCTIONS

FNW.COM

We reserve the right to modify or improve the designs or 

specifications of our products at any time without notice.

20

18. WARRANTY

LIMITED WARRANTY:

Subject to the limitations expressed herein, Seller warrants that products manufactured by Seller shall be free from defects in design, 
material and workmanship under normal use for a period of one (1) year from installation but in no case shall the warranty period extend 
longer than eighteen months from the date of sale. This warranty is void for any damage caused by misuse, abuse, neglect, acts of God, 
or improper installation. For the purpose of this section, “Normal Use” means in strict accordance with the installation, operation and 
maintenance manual. The warranty for all other products is provided by the original equipment manufacturer. 

REMEDIES:

Seller shall repair or replace, at its option, any non-conforming or otherwise defective product, upon receipt of notice from Buyer 
during the Manufacturer’s warranty period at no additional charge. SELLER HEREBY DISCLAIMS ALL OTHER EXPRESSED OR IMPLIED 
WARRANTIES, INCLUDING, WITHOUT LIMITATION, ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS OR FITNESS FOR 
A PARTICULAR PURPOSE. 

LIMITATION OF LIABILITY:

UNDER NO CIRCUMSTANCES SHALL EITHER PARTY BE LIABLE TO THE OTHER FOR INCIDENTAL, PUNITIVE, SPECIAL OR 
CONSEQUENTIAL DAMAGES OF ANY KIND. BUYER HEREBY ACKNOWLEDGES AND AGREES THAT UNDER NO CIRCUMSTANCES, 
AND IN NO EVENT, SHALL SELLER'S LIABILITY, IF ANY, EXCEED THE NET SALES PRICE OF THE DEFECTIVE PRODUCT(S) 
PURCHASED DURING THE PREVIOUS CONTRACT YEAR. 

LABOR ALLOWANCE:

Seller makes NO ADDITIONAL ALLOWANCE FOR THE LABOR OR EXPENSE OF REPAIRING OR REPLACING DEFECTIVE PRODUCTS 
OR WORKMANSHIP OR DAMAGE RESULTING FROM THE SAME. 

RECOMMENDATIONS BY SELLER:

Seller may assist Buyer in selection decisions by providing information regarding products that it manufacturers and those manufactured 
by others. However, Buyer acknowledges that Buyer ultimately chooses the product’s suitability for its particular use, as normally 
signified by the signature of Buyer’s technical representative. Any recommendations made by Seller concerning the use, design, 
application or operation of the products shall not be construed as representations or warranties, expressed or implied. Failure by Seller 
to make recommendations or give advice to Buyer shall not impose any liability upon Seller. 

EXCUSED PERFORMANCE:

Seller will make a good faith effort to complete delivery of the products as indicated by Seller in writing, but Seller assumes no responsibility 
or liability and will accept no back-charge for loss or damage due to delay or inability to deliver, caused by acts of God, war, labor difficulties, 
accidents, inability to obtain materials, delays of carriers, contractors or suppliers or any other causes of any kind whatever beyond the 
control of Seller. Under no circumstances shall Seller be liable for any special, consequential, incidental, or indirect damages, losses, or 
expense (whether or not based on negligence) arising directly or indirectly from delays or failure to give notice of delay. 

©2022 Ferguson Enterprises, LLC  1022 4329371

Summary of Contents for FNW7XX





















Reviews: