background image

!   

SAFETY INFORMATION

 

Please read and understand this entire manual before attempting to assemble, operate or install 

the product.

 

 

!     

WARNING: 

Any use of this appliance other than that recommended by the manufacturer 

in

 

this owners manual may cause fire, burns, electric shock and/or other serious injuries or death.

 

 

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock 

and injury to persons including the following:

 

 

 

1.    Read the manufacturer

’s instructions completely before using this appliance.

 

 

2.    This appliance will become hot when in use. To avoid burns, do not let bare skin touch hot surfaces.    The grill at 

the top of this heater in particular will become hot when the heater is active. Take special care not to block the 

air intake or exhaust vents.

 

3.    Extreme caution is necessary when the appliance is used by or near children or invalids and whenever the heater 

is left operating and unattended.

 

4.      Do  not  operate  the  heater  if  the  power  cord  or  plug  has  been  damaged  or  the  heater  has  been  damaged  or 

malfunctioned in  any way.  Take  the  appliance  to  an  authorized  service  facility  for  examination,  electrical  or 

mechanical adjustment or repair.

 

5.    Do not use outdoors.

 

 

6.    This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater 

where it may fall into a bathtub or other water container.

 

7.    To disconnect the appliance, turn all controls 

“OFF”, and then remove the plug from the electrical outlet.

 

 

8.    The appliance comes equipped with a 3  prong-grounding plug.  Do not cut the grounding prong.  Connect  to 

properly grounded 120V outlets only.

 

9.    Do not insert or allow foreign objects to enter any ventilation or exhaust openings as this may cause an electric 

shock or fire, or damage the appliance.

 

10.  To prevent a possible fire, do not block air intakes or exhausts in any manner. Do not use on soft surfaces, like a 

bed, where openings may become blocked.

 

11.  All electrical heaters have hot and arcing or sparking parts inside.  Do not use in areas where gasoline, paint, or 

flammable liquids are used or stored or where the appliance will be exposed to flammable vapors.

 

12.  Avoid using the appliance with an extension cord.  Extension cords may overheat and cause a risk of fire.  If  an 

extension cord MUST be used, the cord must be No. 16AWG minimum size and rated not less than 1875 W atts. 

The  extension  cord  must  be  a  3-prong  cord  with  grounding  type  plug  and  cord  connection  and  should  not 

exceed 20feet (6m) in length.

 

13.  When  transporting  or  storing  the  heater,  take  care  to  keep  both  the  unit  and  power  cord/plug  dry,  free  from 

excessive vibration and away from heat sources.

 

14.  Use the  heater only as  described in this manual.  Any  other  use  not  recommended  by  the  manufacturer  may 

cause fire, electric shock, or injury to persons.

 

15.  Do not attempt to burn wood or other materials in this heater.

 

 

 

                                                           3

 

Summary of Contents for LEF36













Reviews: