background image

www.fmiproducts.com

126363-01B

9

Figure 5 - Installing Hood 

Screw

Hood

Rail

INSTALLATION

Continued 

Figure 6 - Assembling Perimeter Trim

Side Trim

Slot

Mitered 

Edge

Slot

Shim

Set Screws

Adjusting 

Plate 

Assembled 

Trim

Top 

Trim

Figure 7 - Attaching Perimeter Trim to 

Fireplace

Trim 

Hanging 

Screws

Hanging 

Notches 

on Trim 

Mitered 

Edge

ASSEMBLING AND ATTACHING 

OPTIONAL PERIMETER TRIM

IMPORTANT: 

If you are recessing the firebox 

in a wall, do not attach trim at this time. See 

Built-In Fireplace Installation

, page 11.

Note: These instructions show assembling 

and attaching trim to fireplace.

CHECK GAS TYPE

Use the correct gas type (natural or propane/

LP) for your fireplace. If your gas supply is not 

correct,  do  not  install  fireplace.  Call  dealer 

where you bought fireplace for proper type 

fireplace.

 WARNING: This appliance is 

equipped for natural or propane/

LP gas but not both. Gas type is 

indicated on rating plate. Field 

conversion is not permitted.

ELECTRICAL HOOKUP

This fireplace includes a blower which must 

be connected to either a wall receptacle or 

the electrical receptacle that is included within 

the fireplace. If the receptacle included with 

the fireplace is to be used, it must be wired 

to a 120 volt supply by a certified electrician.

OPTIONAL PANELS

Each fireplace is shipped with louvered panels 

installed.  Smooth panels are also shipped 

with  this  fireplace  and  be  used  if  desired.  

They  allow  for  a  different  appearance. The 

smooth panels may be covered with noncom

-

bustible materials such as ceramic tile or rock.

INSTALLING HOOD

Install hood to rail already installed in fireplace 

as shown in Figure 5. Use 3 Phillips screws 

provided.

1.  Remove packaging from three pieces 

of trim.

2.  Locate four screws, two adjusting plates 

with  set  screws,  and  two  shims  in  the 

hardware packet.

3.  Align shim under adjusting plate as shown 

in Figure 6.

4.  Slide  one  end  of  adjusting  plate/shim 

in slot on mitered edge of top trim (see 

Figure 6).

5.  Slide  other  end  of  adjusting  plate/shim 

in slot on mitered edge of side trim (see 

Figure 6).

6.  While firmly holding edges of trim to-

gether,  tighten  both  set  screws  on  the 

adjusting plate with slotted screwdriver.

7.  Repeat steps 1 through 6 for other side.

8.  Tighten trim hanging screws (#10 x 6.25 

shoulder) into holes in cabinets. Place 

the assembled trim onto fireplace cabinet. 

Align hanging notches on trim with hang

-

ing screws on side of fireplace (see Figure 

7).  Push  trim  firmly  into  place,  sliding 

hanging notches over hanging screws.

Summary of Contents for FSF32NRWS





































Reviews: