background image

www.fmiproducts.com

118197-01D

11

CORNER INSTALLATION

Recommended Applications:

•  Corner ground floor installation

•  Ground floor installation where pipe vents horizon

-

tally through wall (over 12" horizontal pipe)

•  Basement installation where one foot clearance 

from ground to termination is possible

VENTINg INSTALLATION INSTRUCTIONS

Continued

Figure 15 - Horizontal Termination Configuration for Corner Installation Using One 

90° Elbow

Square 
Termination 

Wall 
Firestop

Not to Exceed (H) Limits

As Required 
for (V), See 
Chart for 
Pipe Section 
Required

45° Elbow

90° Elbow

90° Elbow

Square 
Termination

Wall 
Firestop

45° Elbow

12" Min.

Required

Vertical (V)

Vertical Pipe

horizontal (h) 

*43 

1

/

2

" min.

None

30" max.

54 

1

/

2

" min.

1 ft.

48" max.

66 

1

/

2

" min.

2 ft.

60" max.

78 

1

/

2

" min.

3 ft.

84" max.

90 

1

/

2

" min.

4 ft.

20' max.

* Ground Floor Corner Venting 

Not to Exceed 
(H) Limits

SNORKEL TERMINATION INSTALLATION

Recommended Applications:

•  Installations requiring a vertical rise on building exterior

•  Any installation using snorkel termination to achieve one foot above ground

Snorkel terminations are available for installations requiring a vertical rise on the exterior of the building. 

If installing snorkel termination below grade, you must provide proper drainage to prevent water from 

entering snorkel termination (see Figure 16). Do not back fill around snorkel termination.

Snorkel Termination 

12"  
Min.

Snorkel 
Termination

Wall 
Firestop

90° Elbow

45° Elbow

Figure 16 - Snorkel Termination Configurations for Below Ground Installation

Snorkel Termination

Adequate 
Drainage

12" Min.

12" Min.

Summary of Contents for DVC36B





















Reviews: