manualshive.com logo in svg
background image

1

WARNING:  If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life.

-- Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.

-- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier

from a neighbour’s phone.  Follow
the gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the fire department.

--Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.

FOR YOUR SAFETY

IMPORTANT:

THESE INSTRUCTIONS ARE TO

REMAIN WITH THE

HOMEOWNER

061098-36

ESTATE_A

5055.8

INSTALLATION

AND OPERATING

INSTRUCTIONS

SERIES A

DIRECT VENT FIREPLACE

This appliance may be installed in an
aftermarket permanently located,
manufactured (mobile) home, where not
prohibited by local codes.

This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.

f i r e - p a r t s . c o m

Содержание Estate A Series





































Отзывы: