background image

3

ITEMS INCLUDED

3.7 V - 200 mAh Lithium

Polymer Battery

Tape Strips

USB

Charger

(TxR Only)

2.4G Radio
System
(RTF Only)

AA Alkaline

Batteries x 4

(RTF Only)

Completely Assembled
Fuselage

Wing

Tail
Surfaces

Tx-R ADDITIONAL ITEMS REQUIRED

  4-channel SLT Protocol Transmitter

The Micro Calypso can be flown with Tactic transmitters (SLT 

protocol). When doing this please refer to the Tactic radio 
instructions and be aware some channels may need to be 
reversed or re-assigned for proper operation. This includes 
the throttle channel, so extra care must be taken to be sure 
the throttle direction is correct.

TACJ2403  Tactic TTX403 4-Channel SLT Mini Transmitter
TACJ2410  Tactic TTX410 4-Channel SLT System
TACJ2610  Tactic TTX610 6-Channel SLT System
TACJ2650  

Tactic TTX650 6-Channel SLT Computer 

Transmitter

AVAILABLE PARTS

FLZA6470 Fuselage
FLZA6471 Wing
FLZA6472  Tail Surface Set
FLZA6473  Folding Prop Set
FLZA6474  Prop Blade Set
FLZA6475 Spinner/Hub
FLZA6476 Motor Set
FLZA6477 Pushrod Set
FLZA6478 Nose Cone
FLZA6479 USB Charger
FLZA6480 Receiver/Servos
FLZA6481 Gearbox Set
FLZA6482  Motor Shaft Set
FLZA6483  LiPo 3.7V 200 mAh
FLZA6484 Transmitter

PARTS GUIDE

Elevator

Control

Rod

Vertical

Stabilizer

Horizontal

Stabilizer

Rudder

Control

Rod

Wing

Elevator

Rudder

Propeller

RTF TRANSMITTER

MODE 2 SHOWN. SEE PAGE 9 FOR MODE 1.

  1

  Mode Change Switch

  2

 Power 

Switch

  3

 Elevator 

Trim

 (Up/Down)

 

     Adjust up/down so plane flies horizontal.

  4

 Elevator 

Stick

 (Up/Down)

 

     Controls plane’s upwards/downwards movement.

  

Rudder 

Stick

 (Left/Right)

 

     Controls plane’s left/right movement.

  5

 Rudder 

Trim

 (Left/Right)

 

     Adjust left/right so plane flies straight.

  6

 Throttle 

Trim

 (Up/Down)

 

      Adjusts throttle so motor will not move at the down 

position.

  7

 Throttle 

Stick

 (Up/Down)

 

     Controls propeller speed.

  8

 Function 

Selector

 

     Additional details on page 7.

1

2

3

4

5

6

REVERSER

REVERSER

RUDDER ELEVATOR

D/R-Dual Rate

  9

 Power 

Indicator

 10

 Charge 

Lamp

 11

 Battery 

Cover

 12

 Charger 

Cover

Summary of Contents for micro calypso













Reviews: