background image

FLZA3050 RTF / FLZA3052 TxR

SPECIFICATIONS

Wingspan:

24.8 in [630 mm]

Total Length:

19.1 in [485 mm]

Weight:

1.90 oz [54 g]

IMPORTANT

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

For more info, go to the YouTube Hobbico how-to channel.

WARRANTY

Flyzone

®

 guarantees this kit to be free from defects in both 

material and workmanship at the date of purchase. This warranty 
does not cover any component parts damaged by use or 
modification. 

In no case shall Flyzone’s liability exceed the 

original cost of the purchased kit.

 Further, Flyzone reserves 

the right to change or modify this warranty without notice.

In that Flyzone has no control over the final assembly or material 
used for final assembly, no liability shall be assumed nor 
accepted for any damage resulting from the use by the user of 
the final user-assembled product. By the act of using the 
user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated 
with the use of this product, the buyer is advised to return 
this kit immediately in new and unused condition to the 
place of purchase.

For warranty claims contact Hobbico Product Support:

Hobbico Product Support

3002 N. Apollo Drive  Suite 1
Champaign IL  61822  USA

Telephone: (217) 398-8970 ext. 6
Fax: (217) 398-7721
E-mail: [email protected]

I N S T R U C T I O N

M A N U A L

© 2016 Flyzone,

®

  a Hobbico company.

®

  This radio controlled model is not a toy!

  This model must be assembled and operated according to the instructions.

  It may cause serious injury to persons or property if not used responsibly. 

Not suitable for children under 14 years old.

Summary of Contents for micro calypso













Reviews: