background image

 

Packaging content

包装内容

3

 

channel 2.4G transmitter (USM-GT3X)

通2.4

G

发射机(

USM

-

GT3X

)

3

 

channel 2.4G receiver 

(

FS

-

A

3

)

3

 通2.4

G

接收机(

FS

-

A3

)

说明书

User manual

FCC

 

Statement

This

 

equipment

 

has

 

been

 

tested

 

and

 

found

 

to comply with the limits for a Class B digital device pursuant  to part  15  of  the

FCC rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  in  a  residential 
installation. This equipment generates, uses and can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in 
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee 
that interference will not occur in a particular installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or 
televison reception, which can be determined by turning the equipment off and on, the user is encouraged to  try  to  correct 
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued  compliance,  any  changes  or  modifications  not  expressly  approved  by  the  party  responsible  for 
compliance could void the user’s authority to operate this equipment. (Example use  only  shielded  interface  cables  when 
connecting to computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

Caution!

The  manufacturer  is  not  responsible  for  any  radio  or  TV  interference  caused  by  unauthorized  modifications  to  this 
equipment. Such modifications could void the user authority to operate the equipment. 

FCC

 

Statement

3

2

1

1

1

1

声明

6

22

GT3X

DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must 

not be collocated or operating in conjunction with any other antenna or transmitter

 

Summary of Contents for USM-GT3X
























Reviews: