FS-WTM01
http://www.flysky-cn.com
Copyright ©2022 Flysky Technology co., ltd
Wireless trainer unit
实现教练功能
Realize trainer function
若将富斯无蓝牙接口的发射机和非富斯的发射机设置为教练机，请根据发射机实际接口选择 FS-XC002、FS-XC003 或 FS-XC004 转接线来连接无线教练模块与发
射机，设为学员机的发射机则必须是富斯发射机，同样需兼容 AFHDS 2A/AFHDS3 协议，连接参考示意图如下。
常规应用连接示意图：
特殊应用连接示意图：
If you set Flysky transmitter without Bluetooth port and non-Flysky transmitter to trainer transmitter, please choose FS-XC002, FS-XC003 or FS-XC004
cable to connect the wireless trainer unit to the transmitter according to the actual interface of the transmitter. The transmitter which set to student
transmitter must be a Flysky transmitter, which is also compatible with AFHDS 2A/AFHDS 3 protocol. The connection reference diagrams are as below.
Connection diagram for general application:
Connection diagram for special application:
对码
Binding
注：
1. 在无线教练模块通电之前请先设置好三档开关，如发射机使用 AFHDS 3 协议，则将三档开关拨至 AFHDS 3 位置。
2. 对码成功后 , 无线教练模块的 LED 灯常亮；对码时，若十秒内对码没有完成，则 LED 灯进入慢闪闲置状态。
3. 完成对码后，下一次开机无需再次对码。
4. PL18 发射机固件版本需 1.0.55 及以上版本可与本模块对码。
本无线教练模块通电之后即自动进入对码状态。
• 若通过信号接头连接 PL18 发射机通电，则本无线教练模块与另一台发射机对码。
• 若通过 Micro USB 接口连接电源，本模块与两台发射机的其中一台对码，对码成功后，将 Micro USB 接口转接线连接另一台发射机。
三档开关
Switch introduction
三档开关（AFHDS 2A/AFHDS3/UPD）分别对应 AFHDS 2A 和 AFHDS 3 协议对码通讯以及无线更新模式三个选项。请根据实际发射机的无线协议和是否需要更新
固件来选择相应的开关位置。
注：（1）通电前需设置好档位开关，通电后即进入该模式；
（2）若您在无线模块使用过程中重新设置三档开关模式，此操作无效。
The three-level switch (AFHDS 2A/AFHDS 3/UPD) corresponds to the three options of AFHDS 2A and AFHDS 3 protocol binding communication and
wireless update mode respectively. Please select the corresponding switch position according to the actual transmitter's wireless protocol. In addition,
you need to check whether the firmware needs to be updated so as to determine the switch position.
Notes
:
1. The three-level switch needs to be set before power-on. It enters this configured mode after power-on.
2. If you reset the three-level switch mode while the wireless trainer unit is in use, this operation is invalid.
Binding
Model
(receiver)
Binding
Wireless RF
transmission
Wireless RF
transmission
Model
(receiver)
Binding
Binding
S terminal connector
3.5mm audio head
Futaba interface
Wireless RF
transmission
Wireless RF
transmission
Flysky transmitter set to
Trainer
mode (e.g. PL18)
Transmitter set to
Trainer
mode (With S terminal connector)
Transmitter set to
Trainer
mode (With 3.5mm audio interface)
Transmitter set to
Trainer
mode (With Futaba interface)
