FlySky FS-WTM01, Quick Start Manual

Page: 3 / 4

FS-WTM01
http://www.flysky-cn.com
Copyright ©2022 Flysky Technology co., ltd
Wireless trainer unit Wireless trainer unit
对码 Binding
转接线概览 Overview
USB 接口 /Micro USB
FS-XC002
Futaba 接口 /Futaba interface
电源负极 /Power cathode
电源正极 /Power anode
信号 /Signal
产品型号 ：FS-XC002
长度 ：100mm
重量 ：7g
适用范围 ：与带有 Futaba 接口的发射机
连接使用。可连接本无线教练模块，实现
教练功能 。
Futaba 接口 ：连接带有 Futaba 教练接口
的发射机。
USB 接口 ：连接带有 USB 接口的设备，
如本无线教练模块。
Product name : FS-XC002
Length : 100mm
Weight : 7g
Scope of application : Connects to the transmitter
with the Futaba interface.It can be connected to this
wireless trainer unit for the trainer function.
Futaba interface : Connects this interface to the
transmitter with the Futaba interface.
Micro USB : Connects to the devices with USB interface,
such as the wireless trainer unit.
产品型号 ：FS-XC003
长度 ：140mm
重量 ：10g
适用范围 ：与带有 S 端子接口的发射机连
接使用。可连接本无线教练模块，实现教
练功能 。
S 端子接口 ：连接带有 S 端子教练接口的
发射机。
JST 接口 ：为 USB 接口设备供电，供电电
压参考连接的设备，如连接本无线教练模
块，其支持的电压为 3.5~9V/DC，可使用
1-2S 锂电池供电。
USB 接口 ：连接带有 USB 接口的设备，如
本无线教练模块。
FS-XC003
电源负极 /Power cathode
电源正极 /Power anode
电源负极 /Power cathode
信号 1/Signal 1
信号 2/Signal 2
S 端子（90 度弯头）/
S terminal (90 degree bend)
USB 接口 /Micro USB
JST 接口 /JST interface
Product name : FS-XC003
Length : 140mm
Weight : 10g
Scope of application : Connects to the transmitter with
the S terminal interface. It can be connected to this
wireless trainer unit for the trainer function.
S terminal connector : Connects to the transmitter with
the S terminal trainer interface.
JST interface : Power supply for a device with the USB
interface. For the power supply voltage, refer to the
connected device. For example, this wireless trainer
unit supports 3.5 ~9V/DC, which can be powered by
1-2S lithium battery.
Micro USB : Connects to devices with USB interface,
such as this wireless trainer unit.
JST 接口 /JST interface
产品型号 ：FS-XC004
长度 ：100mm
重量 ：7g
适用范围 ：与带有 3.5mm 音频接口的发射
机连接使用。可连接本无线教练模块，实
现教练功能。
3.5mm 音频头 ：连接带有 3.5mm 音频教
练接口的发射机。
JST 接口 ：为 USB 接口设备供电，供电电
压参考连接的设备，如连接本无线教练模
块，其支持的电压为 3.5~9V/DC，可使用
1-2S 锂电池供电。
USB 接口 ：连接带有 USB 接口的设备，如
本无线教练模块。
Product name : FS-XC004
Length : 100mm
Weight : 7g
Scope of application : Connects to the transmitter with
the 3.5 mm audio trainer interface. It can be connected
to ths wireless trainer unit for the trainer function.
3.5 mm audio head : Connects to the transmitter with
the 3.5 mm audio trainer interface.
JST interface ：Power supply for a device with the USB
interface. For the power supply voltage, refer to the
connected device. For example, this wireless trainer
unit supports 3.5 ~9V/DC, which can be powered by 1-2S
lithium battery.
Micro USB : Connects to devices with USB interface,
such as this wireless trainer unit.
FS-XC004
电源负极 /Power cathode
信号 2/Signal 2
信号 1/Signal 1
3.5mm 音频头 /
3.5 mm Audio head
USB 接口 /Micro USB
以本无线教练模块通过连接蓝牙接口通电为例，对码的步骤如下：
1. 接通需要与本无线教练模块对码的发射机电源，并处于对码状态。
2. 将本无线教练模块插入另一台发射机后开机，无线教练模块通电后进入对码状态，等待完成对码。
Notes :
1. Please set the three-level switch before the wireless trainer unit is powered on. For an example, if the transmitter uses AFHDS 3 protocol, toggle the
three-level switch to the AFHDS 3 position.
2. When the binding is completed, the LED indicator should be solid on. If the binding is not completed within ten seconds, the LED indicator will enter
its slow flashing state.
3. After the binding is completed, there is no need to bind again when the wireless trainer unit is to be powered on next time.
4. PL18 Transmitter with the firmware version 1.0.55 or above can bind with this wireless trainer unit.
The wireless trainer unit will enter bind mode after power-on automatically.
• If the wireless trainer unit is connected to the bluetooth port of PL18 transmitter, then the wireless trainer unit will be powered by PL18 transmitter,
the wireless trainer unit needs to bind with another transmitter.
• If the wireless trainer unit is powered by the power supply via USB interface, then the wireless trainer unit should bind with either of the two
transmitters. After the bind is successful, connect the other transmitter to the another end of the USB cable.
As an example, follow the following steps for binding, if the wireless trainer unit is connected to the bluetooth port of the transmitter:
1. Power on the transmitter that needs to bind with this wireless trainer unit, then put it in the bind mode.
2. Plug the wireless trainer unit to the other transmitter via the signal plug, then power on the transmitter. The wireless trainer unit enters the bind mode
after power-on.
当您使用的教练机非富斯 PL18 发射机时，本无线教练模块可以与有 Futaba 接口、S 端子或 3.5mm 音频接口的发射机通过如下几款转接线连接，实现教练功能。
When you choose other transmitter as a trainner transmitter instead of PL18 transmitter, this wireless trainer unit can connect the transmitter which has
Futaba interface, S terminal connector or 3.5 mm Audio head through the cabels listed below to realize the trainer function.