FS-WTM01
http://www.flysky-cn.com
Copyright ©2022 Flysky Technology co., ltd
Wireless trainer unit
感谢您购买富斯无线教练模块，选用本模块，就可以实现教练机与
学员机无线连接，让您省却配备专门的教练线，感受更多乐趣。
Thank you for purchasing Flysky wireless trainer unit. By choosing this unit, you can
realize the wireless connection between trainer transmitter and student transmitter.
In this way, the special trainer cable is not required.
产品介绍
Introduction
产品概览
Overview
产品规格
Specifications
[1] USB 接口
[2] LED 指示灯
[3] 信号接头
[4] 信号接头保护帽
[5] 三档开关 (AFHDS 2A/AFHDS 3/UPD）
[1] Micro USB
[2] LED
[3] Signal plug
[4] Protective cover
[5] Three-level switch (AFHDS 2A/AFHDS 3/UPD）
接口介绍
Interface introduction
本无线教练模块有一个 Micro USB 接口和一个信号接头。
USB 接口
无线教练模块通过 USB 接口，既可以实现为本模块供电，又可以实现教
练功能。
• USB 接口供电：将 FS-XC002、FS-XC003 或 FS-XC004 转接线与无线教
练模块 USB 接口连接后，可通过 USB 接口由 FS-XC003 或 FS-XC004 转
接线的 JST 接口连接电源或由 FS-XC002 转接线所连接遥控设备的电源为
无线教练模块供电。
信号接头
无线教练模块通过信号接头与 PL18 发射机相连接，既实现通道数据传输，
又可以通过发射机界面查看相关信息。
• 信号接头供电：将无线教练模块连接 PL18 发射机的蓝牙接口。
注
：
1. USB 接口与信号接头独立供电，优先选用信号接头供电；
2. 若不使用信号接头时，请不要取下信号接头保护帽，以保护信号接头；
3. PL18 发射机固件需 1.0.65 及以上版本才可通过信号接头与无线教练
模块通信。
无线教练模块与 PL18 发射机蓝牙接口连接的示意图如下：
产品型号：FS-WTM01
适配发射机：PL18 等 AFHDS 3 或 AFHDS 2A 协议发射机
通道个数：18
无线频率：2.4GHz ISM
无线协议：AFHDS 2A/AFHDS 3
天线类型：内置天线
遥控距离：>50 米
USB 接口供电范围：3.5V ～ 9V/DC
发射功率：<13dBm
USB 接口数据输出类型：PPM
温度范围：-10℃ ~ +60℃
湿度范围：20% ~ 95％
在线更新：支持
外形尺寸：42.2mm*18mm*6.6mm
重量：
4.5g
认证：CE、FCC ID: N4ZWTM0100
Product Name: FS-WTM01
Adaptive Transmitter: Transmitters with AFHDS 3 protocol(such
as PL18) or transmitters with AFHDS 2A protocol
Numbers of Channels: 18
RF: 2.4GHz ISM
Protocol: AFHDS 2A/AFHDS 3
Antenna: Built-in antenna
Distance: >50m
Input Power for USB interface: 3.5V ～ 9V/DC
Maximum Power: <13dBm(E.I.R.P.) (EU)
Data Output for USB Interface: PPM
Temperature Range: -10℃ ~ +60℃
Humidity Limit: 20% ~ 95%
Online Update: Yes
Dimension:
42.2mm*18mm*6.6mm
Weight: 4.5g
Certifications: CE, FCC ID:
N4ZWTM0100
1、电源正极
2、信号输出端 1
3、信号输出端 2
4、 /
5、 电源负极
1、Power anode
2、Signal 1
3、Signal 2
4、 /
5、 Power cathode
[1]
[4]
[2]
[3]
[5]
54321
This wireless trainer unit has a micro USB interface and a signal
plug.
Micro USB interface
The wireless trainer unit can realize power supply and trainer
function through this micro USB interface.
• Power supply through the micro USB interface: FS-XC002, FS-
XC003 or FS-XC004 cables are required to realize power supply
through the micro USB interface. The supply power for the
wireless trainer unit is implemented by connecting these cables
through mirco USB interface: Supply power for the wireless
trainer unit via the power supply connected by the JST interface
of FS-XC003 or FS-XC004 cable, or the device connected by FS-
XC002 cable.
Signal plug
The wireless trainer unit (FS-WTM01) is connected to the PL18
transmitter through the signal plug to transfer datas. You can view
the information related to the wireless trainer unit on the main
interface of the transmitter.
• Power supply through the signal plug: Connects the signal plug
of the wireless trainer unit to the Bluetooth port of the PL18
transmitter.
Notes
:
1. The power supply of the micro USB interface and signal plug
is provided independently. The signal plug supply is preferred.
2. If you don't use the signal plug, please don't take off the
signal plug protective cover. This protective cover is for the
protection of the signal plug.
3. The PL18 transmitter with firmware version 1.0.65 or above
can connect with the wireless trainer unit through the signal
plug.
Connecting to the Bluetooth port of PL18 transmitter is showing
on the left, for your reference.
