background image

2.

Before use, examine cable for damage.  If there are
signs of damage or ageing, it must be replaced by
the manufacturers service agent or a similar qualified
person to avoid hazard.

3.

Do not use the trimmer if the electric cables are dam-
aged or worn. 

4.

Immediately disconnect from the mains electricity sup-
ply if the cable is cut, or the insulation is damaged.  Do
not touch the electric cable until the electrical supply
has been disconnected.  Do not repair a cut or dam-
aged cable.  Replace it with a new one.  

5.

Your extension cable must be uncoiled, coiled cables
can overheat and reduce the efficiency of your trimmer.

6.

Keep the cable clear of the cutting area and obsta-
cles at all times.

7.

Do not pull cable around sharp objects.

8.

Always switch off at the mains before disconnecting
any plug, cable connector or extension cable.

9.

Never pull on the cable to disconnect any of the plugs.

10. Switch off, remove plug from mains and examine electric

supply cable for damage or ageing before winding cable for
storage.  Do not repair a damaged cable, replace it with a
new one.  Use only Flymo replacement cable.

11. Always wind cable carefully, avoiding kinking.
12. Use only on AC mains supply voltage shown on the

product rating label.

13. Flymo trimmers are double insulated to EN60335.

Under no circumstance should an earth be con-
nected to any part of the trimmer.

Preparation
1.

While using your product always wear substantial
footwear and long trousers.

2.

Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.

3.

Inspect the area to be cut before each use. Remove
all objects such as stones, broken glass, nails, wire,
string etc, which can be thrown or become entangled
in the trimmer head.

4.

Before use, inspect the area for wildlife, especially
hedgehogs.

5 .

Check that the cutting head is fitted correctly.

Use
1.

Use the trimmer only in daylight or good artificial light.

2.

Avoid operating your trimmer in wet grass, where feasible.

3.

Take care in wet grass, you may lose your footing. 

4.

On slopes, be extra careful of your footing and wear
non-slip footwear.

5.

Do not walk backwards when trimming, you could
trip. Walk never run.

6.

Keep cutting head below waist level.

7.

Switch off before pushing the trimmer over surfaces
other than grass.

8.

Never operate the trimmer with damaged guards or
without guards in place.

9.

Never fit metal cutting elements.

10. Keep hands and feet away from the cutting means at

all times and especially when switching on the motor.

11. Never pick up or carry a trimmer by the cable.
12. Do not lean over the trimmer guard - objects may be

thrown by the cutting line.

13. Remove the plug from the mains :
-

before leaving the trimmer unattended for any period;

-

before clearing a blockage;

-

before checking, cleaning or working on the appliance;

-

if you hit an object.  Do not use your trimmer until you are
sure that the entire trimmer is in a safe operating condition;

-

if the trimmer starts to vibrate abnormally.  Check im-
mediately.  Excessive vibration can cause injury.

Maintenance and storage
1.

Keep all nuts, bolts and screws tight to be sure the
trimmer is in safe working condition.

2.

Replace worn or damaged parts for safety.

3.

Only use the replacement cutting line specified for
this product.

4.

Only use replacement parts and accessories recom-
mended by Husqvarna UK Ltd.

5.

After any maintenance in dealing with the cutting line,
always return the product to its normal operating posi-
tion before switching on.

6.

To avoid the risk of injury keep fingers and hands clear
of the line cutter on the leading edge of the guard.

7.

Inspect and maintain the trimmer regularly.  Any re-
pairs must be carried out by an authorised repairer.

8.

Store in a cool dry place and out of reach of children.
Do not store outdoors.

9.

Allow the product to cool for at least 30 minutes be-
fore storing.

Cables

IMPORTANT
Use only 1.00mm

2

size cable up to 40 metres length

maximum.
Maximum rating:
1.00mm

2

size cable, 10 amps 250 volts AC.

THE POWER TRIM IS SUPPLIED WITH AN ELEC-
TRIC MAINS CABLE WIRED DIRECTLY INTO THE
PRODUCT.

1.

Flymo Mains Cables and Extension Cables are avail-
able from your local Approved Service Centre.

2.

Do not wire an extension cable directly to your product
yourself.  Please contact your local Approved Service
Centre for further information on the connectors and
kits available.

3.

Only use extension cables specifically designed for
outdoor use.

CONNECTORS
Flymo connectors are suitable for use with 2 core cable
only.  Under no circumstances should these connectors
be used for earthed products.
All Flymo connectors and cables are of splashproof con-
struction.  They are not waterproof and must not be left
outside permanently nor should they be submerged or
immersed in water.  Do not let cable lay or trail through
pools of water or splashed with water from hose pipes.
MAINS PLUG REPLACEMENT

If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is in-
serted into a 13 amp socket.

1.

No earth required. Flymo products are double insu-
lated to EN60335 and under no circumstances
should an earth be connected to any part of the prod-
uct.

2.

Ensure the mains voltage suits your product.

3.

IMPORTANT!

The wires in the mains lead are coloured in accordance
with the following code:
BLUE -

NEUTRAL

BROWN

-

LIVE

The wire which is coloured BLUE must be connected to
the Terminal which is marked with the letter ‘N’ or
coloured BLACK.  The wire which is coloured BROWN
must be connected to the Terminal which is marked with
the letter ‘L’ or coloured RED.
4.

It is important that the outer sheath is clamped cor-
rectly into the 3-pin plug.

5.

If in doubt consult your local Service Repairer or qual-
ified electrician before the machine is used.

6.

A 13 Amp fuse must be fitted to the Mains Plug.

7.

The normal plug fuse and household fuse only pro-
tect the electrical equipment and are not a safeguard
against electrocution.

If your product is hard wired i.e. non-detachable mains
electric cable, a conversion kit and extension cable is
available from all Approved Service Centres which can
be found in your local Yellow Pages.

Summary of Contents for Power Trim SET250










Reviews: